This is a multipart message in MIME format.
--===============5073684026444423203==
This is a multipart message in MIME format.
--=_alternative 0002C5488525800A_=
Jimmie,
My advise is to no waste you time/money on the little ones. They are good
for mulching leaves and that is about it.
You can brake the branches faster than they will 'chip' them.
Around here, there is always people putting those things on the curb after
only using them once or twice.
Unless the machine has an autofeed and an MASSIVE flywheel, they aren't
worth it.
Sent from my Commodore 64 on a 2400 Baud Modem.
Eric P
"Be as beneficent as the sun or the sea, but if your rights as a rational
being are trenched on, die on the first inch of your territory." Ralph
Waldo Emerson
----- Forwarded by Eric Petrevich/Megageek on 08/08/2016 08:28 PM -----
From: Jimmie Mayfield <mayfield+shoptalk@sackheads.org>
To: shop-talk@autox.team.net
Date: 08/08/2016 11:35 AM
Subject: [Shop-talk] Small wood chipper recommendations?
Sent by: "Shop-talk" <shop-talk-bounces@autox.team.net>
Tangentially shop/garage-related in that I'll have to store it in my
garage... :) I'm in the market for a small wood chipper and floor space
in my garage is fairly limited so something with the footprint of a
pressure washer or small snowblower (or smaller) would be ideal.
I'm not opposed to an electric model if they perform well but the
youtube videos I've seen tend to show them chewing on finger-sized twigs
fed one at a time. I've also read they often clog when fed green
material and when the knives dull.
I haven't seen many compact gas-powered chippers come across Craigslist.
I'm not opposed to disassembling the chutes for storage though my
first choice would be to find one that doesn't have big horizontal
chutes to begin with.
So a few questions for the group:
1) If you have an electric wood chipper, how well does it work on
branches up to, say, an 1-1.5 inch diameter? I figure anything bigger
I'll just cut manually but if the real-world limits are 1/2-inch with
only an occasional branch larger than 1-inch, then perhaps I should
abandon the electric idea. Are the reports of frequent clogging true?
2) If you have a small gas chipper, how big is the engine? I've seen a
couple on Craigslist with smallish 3.5hp engines though most seem to be
in the 8-11hp range. Roughly, what's the storage footprint?
Thanks!
Jimmie
_______________________________________________
--=_alternative 0002C5488525800A_=
<font size=2 face="sans-serif">Jimmie,</font>
<br>
<br><font size=2 face="sans-serif">My advise is to no waste you time/money
on the little ones. They are good for mulching leaves and that is
about it.</font>
<br>
<br><font size=2 face="sans-serif">You can brake the branches faster than
they will 'chip' them.</font>
<br>
<br><font size=2 face="sans-serif">Around here, there is always people
putting those things on the curb after only using them once or twice.</font>
<br>
<br><font size=2 face="sans-serif">Unless the machine has an autofeed and
an MASSIVE flywheel, they aren't worth it.</font>
<br><font size=2 face="sans-serif"><br>
<br>
Sent from my Commodore 64 on a 2400 Baud Modem.<br>
Eric P<br>
"Be as beneficent as the sun or the sea, but if your rights as a rational
being are trenched on, die on the first inch of your territory." Ralph
Waldo Emerson </font>
<br><font size=1 color=#800080 face="sans-serif">----- Forwarded by Eric
Petrevich/Megageek on 08/08/2016 08:28 PM -----</font>
<br>
<br><font size=1 color=#5f5f5f face="sans-serif">From:
</font><font size=1 face="sans-serif">Jimmie Mayfield
<mayfield+shoptalk@sackheads.org></font>
<br><font size=1 color=#5f5f5f face="sans-serif">To:
</font><font size=1 face="sans-serif">shop-talk@autox.team.net</font>
<br><font size=1 color=#5f5f5f face="sans-serif">Date:
</font><font size=1 face="sans-serif">08/08/2016 11:35 AM</font>
<br><font size=1 color=#5f5f5f face="sans-serif">Subject:
</font><font size=1 face="sans-serif">[Shop-talk]
Small wood chipper recommendations?</font>
<br><font size=1 color=#5f5f5f face="sans-serif">Sent by:
</font><font size=1 face="sans-serif">"Shop-talk"
<shop-talk-bounces@autox.team.net></font>
<br>
<hr noshade>
<br>
<br>
<br><tt><font size=2>Tangentially shop/garage-related in that I'll have
to store it in my <br>
garage... :) I'm in the market for a small wood chipper and floor
space <br>
in my garage is fairly limited so something with the footprint of a <br>
pressure washer or small snowblower (or smaller) would be ideal.<br>
<br>
<br>
I'm not opposed to an electric model if they perform well but the <br>
youtube videos I've seen tend to show them chewing on finger-sized twigs
<br>
fed one at a time. I've also read they often clog when fed green
<br>
material and when the knives dull.<br>
<br>
I haven't seen many compact gas-powered chippers come across Craigslist.
<br>
I'm not opposed to disassembling the chutes for storage though my
<br>
first choice would be to find one that doesn't have big horizontal <br>
chutes to begin with.<br>
<br>
So a few questions for the group:<br>
<br>
1) If you have an electric wood chipper, how well does it work on <br>
branches up to, say, an 1-1.5 inch diameter? I figure anything bigger
<br>
I'll just cut manually but if the real-world limits are 1/2-inch with <br>
only an occasional branch larger than 1-inch, then perhaps I should <br>
abandon the electric idea. Are the reports of frequent clogging true?<br>
<br>
2) If you have a small gas chipper, how big is the engine? I've seen
a <br>
couple on Craigslist with smallish 3.5hp engines though most seem to be
<br>
in the 8-11hp range. Roughly, what's the storage footprint?<br>
<br>
Thanks!<br>
<br>
Jimmie<br>
_______________________________________________<br>
<br>
</font></tt>
--=_alternative 0002C5488525800A_=--
--===============5073684026444423203==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Shop-talk@autox.team.net
Archive: http://www.team.net/archive
--===============5073684026444423203==--
|