--===============2569320922928832798==
boundary="----=_Part_2978661_1578966808.1594131994255"
------=_Part_2978661_1578966808.1594131994255
Content-Transfer-Encoding: quoted-printable
John,Are all 3 carb interconnecting throttle linkages disconnected during a=
ll the tuning steps?=C2=A0I have never seen this test before in any literat=
ure, so I have never tried the test on my tri-carb setup. I will give it a =
try later today & let you know what I find.If your 3 carbs all perform the =
same on all the other tests, I think they will perform correctly together. =
I am assuming you have confirmed that all 3 carbs have the same needle. Als=
o, when you say the "piston is lifted all the way up" you are referring to =
lifting the piston by the pin, (approximately 1/2" pin travel), not by lite=
rally lifting the piston all the way up.Gary Hodson
-----Original Message-----
From: John Spaur via Healeys <healeys@autox.team.net>
To: healeys@autox.team.net
Sent: Mon, Jul 6, 2020 9:07 pm
Subject: Re: [Healeys] HS4 Tri-carb tuning
#yiv2118873180 #yiv2118873180 -- _filtered {} _filtered {} _filtered {}#yiv=
2118873180 #yiv2118873180 p.yiv2118873180MsoNormal, #yiv2118873180 li.yiv21=
18873180MsoNormal, #yiv2118873180 div.yiv2118873180MsoNormal {margin:0in;ma=
rgin-bottom:.0001pt;font-size:11.0pt;font-family:sans-serif;}#yiv2118873180=
a:link, #yiv2118873180 span.yiv2118873180MsoHyperlink {color:#0563C1;text-=
decoration:underline;}#yiv2118873180 a:visited, #yiv2118873180 span.yiv2118=
873180MsoHyperlinkFollowed {color:#954F72;text-decoration:underline;}#yiv21=
18873180 pre {margin:0in;margin-bottom:.0001pt;font-size:10.0pt;}#yiv211887=
3180 span.yiv2118873180HTMLPreformattedChar {font-family:Consolas;}#yiv2118=
873180 span.yiv2118873180EmailStyle19 {font-family:sans-serif;color:windowt=
ext;}#yiv2118873180 span.yiv2118873180EmailStyle20 {font-family:sans-serif;=
color:#1F497D;}#yiv2118873180 .yiv2118873180MsoChpDefault {font-size:10.0pt=
;} _filtered {}#yiv2118873180 div.yiv2118873180WordSection1 {}#yiv211887318=
0 Bob, raising the piston 1/32=E2=80=9D is not my issue. I am wondering why=
the engine stalls when the center carb piston is lifted all the way up and=
the others don=E2=80=99t stall the engine when lifted all the way up. I se=
nt another post with a link for that. The carbs are well synced, I used the=
S.U tuning kit to check the piston lift and they are spot on. =C2=A0thodso=
n@aol.com
------=_Part_2978661_1578966808.1594131994255
Content-Transfer-Encoding: quoted-printable
<div style=3D"color:black;font: 12pt Comic Sans MS, sans-serif;">John,
<div>Are all 3 carb interconnecting throttle linkages disconnected during a=
ll the tuning steps? </div>
<div>I have never seen this test before in any literature, so I have never =
tried the test on my tri-carb setup. I will give it a try later today &=
let you know what I find.</div>
<div>If your 3 carbs all perform the same on all the other tests, I think t=
hey will perform correctly together. I am assuming you have confirmed that =
all 3 carbs have the same needle. Also, when you say the "piston is lifted =
all the way up" you are referring to lifting the piston by the pin, (approx=
imately 1/2" pin travel), not by literally lifting the piston all the way u=
p.</div>
<div>Gary Hodson<br>
<br>
<br>
<div style=3D"font-family:arial,helvetica;font-size:10pt;color:black">-----=
Original Message-----<br>
From: John Spaur via Healeys <healeys@autox.team.net><br>
To: healeys@autox.team.net<br>
Sent: Mon, Jul 6, 2020 9:07 pm<br>
Subject: Re: [Healeys] HS4 Tri-carb tuning<br>
<br>
<div id=3D"yiv2118873180"><style>#yiv2118873180 #yiv2118873180 --
=20
_filtered {}
_filtered {}
_filtered {}
#yiv2118873180 =20
#yiv2118873180 p.yiv2118873180MsoNormal, #yiv2118873180 li.yiv2118873180Mso=
Normal, #yiv2118873180 div.yiv2118873180MsoNormal
=09{margin:0in;margin-bottom:.0001pt;font-size:11.0pt;font-family:sans-seri=
f;}
#yiv2118873180 a:link, #yiv2118873180 span.yiv2118873180MsoHyperlink
=09{color:#0563C1;text-decoration:underline;}
#yiv2118873180 a:visited, #yiv2118873180 span.yiv2118873180MsoHyperlinkFoll=
owed
=09{color:#954F72;text-decoration:underline;}
#yiv2118873180 pre
=09{margin:0in;margin-bottom:.0001pt;font-size:10.0pt;}
#yiv2118873180 span.yiv2118873180HTMLPreformattedChar
=09{font-family:Consolas;}
#yiv2118873180 span.yiv2118873180EmailStyle19
=09{font-family:sans-serif;color:windowtext;}
#yiv2118873180 span.yiv2118873180EmailStyle20
=09{font-family:sans-serif;color:#1F497D;}
#yiv2118873180 .yiv2118873180MsoChpDefault
=09{font-size:10.0pt;}
_filtered {}
#yiv2118873180 div.yiv2118873180WordSection1
=09{}
#yiv2118873180 </style>
<div>
<div class=3D"yiv2118873180WordSection1">
<div class=3D"yiv2118873180MsoNormal"><span style=3D"color:#1F497D;">Bob, r=
aising the piston 1/32=E2=80=9D is not my issue. I am wondering why the eng=
ine stalls when the center carb piston is lifted all the way up and the oth=
ers don=E2=80=99t stall the engine when lifted all the way up. I sent anoth=
er post with a link for that. The carbs are well synced, I used the S.U tun=
ing kit to check the piston lift and they are spot on.</span></div>
<div class=3D"yiv2118873180MsoNormal"><span style=3D"color:#1F497D;">  =
;</span></div>
<div class=3D"yiv2118873180yqt2573448890" id=3D"yiv2118873180yqt21467">
<div>
<div style=3D"border:none;border-top:solid #E1E1E1 1.0pt;padding:3.0pt 0in =
0in 0in;">
<div class=3D"yiv2118873180MsoNormal"><a shape=3D"rect" href=3D"http://auto=
x.team.net/mailman/options/healeys/warthodson@aol.com" target=3D"_blank" st=
yle=3D"font-size: 10pt;">thodson@aol.com</a><br>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
<div class=3D"yqt2573448890" id=3D"yqt39172"><br clear=3D"none"></div>
</div>
</div>
</div>
------=_Part_2978661_1578966808.1594131994255--
--===============2569320922928832798==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============2569320922928832798==--
|