As Glenn pointed out ID to OD taper happens with some pads.?Can
also be a sign of loose wheel bearings.?
But probably as he describes due to higher rubbing speed on OD.?
You can easily taper cut the pads with a 4? diamond masonry blade from just
about any hardware or Lowe?s. You can do it with any number of ways even a
hacksaw but anything but diamond will wear quickly
Get Outlook for iOS
On Wed, Jul 11, 2018 at 2:08 PM -0400, "timmmurphh--- via Fot" <fot at
autox.team.net> wrote:
?
?
From: timmmurphh at gmail.com <timmmurphh at gmail.com>
Sent: Wednesday, July 11, 2018 8:36 AM
To: 'DAVE HOGYE' <dlhogye at comcast.net>
Subject: RE: [Fot] brake pad and rotor discovery and update
?
Thanks for this report.? We have had some issues with the Carbotech pads on our
TR4 at Blackhawk and the Kcup.? We use the CT2-XP10 compound.? I will check our
pad to caliper slot clearance.? Does anyone know offhand of the slot on the 16P
calipers on our TR4 is the same as the TR3 at 3.095??
?
Tim Murphy
#317 TR4
?
From: Fot <fot-bounces at autox.team.net> On Behalf Of DAVE HOGYE via Fot
Sent: Tuesday, July 10, 2018 3:22 PM
To: Friends of Triumph <Fot at autox.team.net>
Subject: [Fot] brake pad and rotor discovery and update
?
Hello Friends,
I have been finding out quite a bit about the unusual and developing front
brake pad, rotor and caliper issues that I have discovered on my TR3.
?
What I found was that the Carbotech CT-57 pads were causing the problem.
?
The supporting or backing plates of the pads had been ground down at Carbotech,
far under the normal plate width that I measured in 4 other production pads
that I have on hand.? Besides that, they were not ground down squarely.
??
This allowed the piston to take tremendous side load under braking causing the
uneven and diagonal wear pattern in the pads.? This also caused the rotor to
contact the caliper as the pads took on heavy uneven wear.
??
The slot in the TR6 caliper is 3.095" and the four non-Carbotech pads sets have
a plate width of no less than 3.082".? The Carbotech plates have an out of
square measurement of 3.030-3.050".? That's as much as .065" clearance in the
caliper slot.??
The plates have too much clearance.? I found that a maximum of .010" backing
plate to caliper slot clearance is more normal.? One set of pads have only
.005" clearance.?
?
Furthermore, the corners of the Carbotech plates and pads were ground down far
enough that the lower end of the pads hardly made contact with the caliper slot
allowing more stress on the caliper piston.
?
I have been going back and forth with Carbotech on this matter and I will be
sending back the badly worn set along with a brand set that have the same
production issues.? I bought the two sets at the same time last August.??
?
What I found is that any backing plates that show evidence of sanding or
grinding marks should be measured for proper clearance, but that really, there
should be no sanding or grinding marks...ever.
?
All of the other pads I have show no evidence of sanding or grinding marks.?
The previously shaped friction pads are cleanly attached to the backing plates
and the backing plate is revealed around the friction material.? Only the
backing plate makes contact with the caliper slot.??
?
It looks like I have to find another race pad supplier.??
?
Thoughts?
?
Dave H.
831-234-4928
?
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/fot/attachments/20180711/65848c47/attachment.html>
-------------- next part --------------
_______________________________________________
fot at autox.team.net
http://www.fot-racing.com
Archive: http://www.team.net/pipermail/fot
|