fot
[Top] [All Lists]

Re: [Fot] Best Stromberg Carbs

To: Joe Alexander <n197tr4@cs.com>
Subject: Re: [Fot] Best Stromberg Carbs
From: Robert Deanes <rfdeanes@gmail.com>
Date: Wed, 28 Mar 2012 09:09:07 -0400
Cc: fot@autox.team.net
Delivered-to: fot-archive@autox.team.net
Delivered-to: fot@autox.team.net
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=20120113; h=mime-version:in-reply-to:references:date:message-id:subject:from:to :cc:content-type; bh=/waiaeruLCWwFujwbLeEd89N87g7zXB4tsci1bRL3W8=; b=EHhwO7k2qqAkJImAQ96YzqHRBOrUQF7ZxmdKSBzAmXlJlqEI4/PxbePahr5DGQrsa6 +bFe9PjHR0yoGzH0nWT+1N8FHIHZlagcDR9X7wVimL2zWrCaoeVIjPx907pjJCXIKtuf pWiVqzbNL1VnaTJR3Z4pw1tr3Y6xCfQssyrazSEy8buis7D1xEbShQOW5KnQyVPzNoDy Vpo1w4R7Q0VftT3KX9VM5gdlvgWhZoUtRXbe8TT7II7doczdWabdip9Uy7oEqw8249MW RX0+XrzCT+Sppge21MR/FzD7hF6QwUWiD4MRzK53XGMxD2byDpGMuEwbSBnWa7Kb8s8c O9ow==
List-archive: <http://autox.team.net/pipermail/fot>
List-help: <mailto:fot-request@autox.team.net?subject=help>
List-id: Friends of Triumph <fot.autox.team.net>
List-post: <mailto:fot@autox.team.net>
List-subscribe: <http://autox.team.net/mailman/listinfo/fot>, <mailto:fot-request@autox.team.net?subject=subscribe>
List-unsubscribe: <http://autox.team.net/mailman/options/fot>, <mailto:fot-request@autox.team.net?subject=unsubscribe>
References: <cfdb8b02b18f4e16afea989a3790e624.gregmogdoc@surfnetusa.com> <Pine.LNX.4.62L.1203280745570.2743@isis.mit.edu> <8CEDAF2D4A09BFF-1C78-8562@webmail-m080.sysops.aol.com>
Joe Curto can help you out with the needles

On Wed, Mar 28, 2012 at 8:10 AM, Joe Alexander <n197tr4@cs.com> wrote:

>  i think most folks know that SU needles can be used in Stromberg carbs
> with
> the use of shim stock.
>
> thought i would mention it, anyway.
>
> it provides a lot of choices
>
>
>
> Joe Alexander
> A. R. E.
> 645 1st Street
> Jesup, Iowa 50648
> 319.464.4711  (cell)
> n197tr4@cs.com
>
>
>
>
>
> -----Original Message-----
> From: Robert M. Lang <lang@isis.mit.edu>
> To: gregmogdoc <gregmogdoc@surfnetusa.com>
> Cc: fot <fot@autox.team.net>
> Sent: Wed, Mar 28, 2012 6:58 am
> Subject: Re: [Fot] Best Stromberg Carbs
>
>
> Hi,
>
> Speaking of which - what needles are folks using in their TR6's with
> Strombergs? I installed alternate needles a while back, and never wrote
> down what they are. I'm pretty sure they're B1AR's from a Jag, but I
> cannot confirm that (yet).
>
> In any case, these needles seem to be a tad rich and I need to confirm
> that with a couple of chassis dyno runs.
>
> In the meantime, I'd appreciate any feedback on the matter.
>
> The following is an interesting article on replacing the fixed needles on
> the early c cylinder federal spec. carbs (TR250 and early TR6):
>
> http://www.buckeyetriumphs.org/technical/Carbs/AdjNeedle/AdjNeedle.htm
>
> regards,
> rml
> ---------------------------------------------------------------------------
> Bob Lang              Triumph TR6!!            |  This space for rent
> Former NER Solo Chair                          |
> Voice:617-253-7438                             |  Cell: 339-927-4489
> ---------------------------------------------------------------------------
> _______________________________________________
> fot@autox.team.net
>
> http://www.fot-racing.com
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe: http://autox.team.net/mailman/options/fot/n197tr4@cs.com
>  _______________________________________________
> fot@autox.team.net
>
> http://www.fot-racing.com
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe: http://autox.team.net/mailman/options/fot/rfdeanes@gmail.com
>
>
>


-- 
rob deanes
TR Racer
_______________________________________________
fot@autox.team.net

http://www.fot-racing.com

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe: 
http://autox.team.net/mailman/options/fot/fot-archive@autox.team.net



<Prev in Thread] Current Thread [Next in Thread>