fot
[Top] [All Lists]

Re: [Fot] Part Number ID help!!!

To: fot@autox.team.net
Subject: Re: [Fot] Part Number ID help!!!
From: Larry Young <cartravel@pobox.com>
Date: Sun, 17 Jul 2011 12:15:35 -0500
I don't believe that is a Triumph OD (at least not a big Triumph).  Is 
it an A type or J type?  I believe the A type overdrives were 22% ratio 
and the J-type overdrives used in the TR6 were 25/115838 and 25/1158976.

I have profiled several Crane cams and have a master catalog of their 
profiles.  That one is not amongst them.  244 is usually the duration at 
0.050.

On 7/17/2011 11:13 AM, Diesel Performance Parts - Info wrote:
> Hey Members,
>
> I got a slug of blocks etc that I need help identifying, can you'll help??
>
> Part                              Numbers that are cast into it somewhere on
> the part
>
> Intake Manifold             307265  V2989   A 1147 aluminum intake I think??
> Gear reduction starter    R-33037
> Koni Shocks                 80-1005
> Trans Overdrive Unit      25/633301    015107     6  875  Laycock Tag info
> Cannon Dual Intake       806  or 908 depends which way you hold it. Looks to
> be an 1300/1500 dual Webber but I don't know.
> Crankshaft                    WDB  W2156  308737   17746N  JOSB   Supposedly a
> new never run crank that has been hard chromed Mains are 2.3" and rods are
> 1.88"
> Transmission                 88306468   V3038          10 spline 1.15" Shaft
> at the splines. Has aluminum bell housing with the slave @ 2 o clock and
> starter on passenger side
> Transmission                 88306468  V3038           10 spline 0.90" Shaft
> has aluminum bell housing with slave at 9 o clock and starter on left side
> Block                            311255 (between freeze plugs) FK5785HE, mains
> are 2.44" recessed cylinder bores
> Block                            305380 (between freeze plugs)   GA42748HE, by
> dipstick is N111, mains are 2.130"
> Block                            307553 (between freeze plugs), Been decked so
> no deck surface number, mains are 2.44" and the bore is 2.94"
> Head                            6 Port N61 by lifter area, T27, 304955
> Head                            8 port with D shaped exhaust outlet, 367871,
> 56
> Head                            8 port with round exhaust port outlet, RKO,
> 27B6, 0589
> Crane Camshaft            F-244 210-8, BN3437
> Flywheel                       Aluminum with replaceable friction area steel
> insert, 50-522
> Pistons                         17753B
> Carrillo rods                  Big end 2.0", small end 0.810, center to center
> is 6.0"
> Cam bearings                1-363, CSB612, 730883M, 84-25-970
> Push rods                     New chrome moly 6.0" length???
>
> Thanks so much for any help you an provide.
>
> Mark Craig
> Diesel Performance Parts, INC.
> 411 Allied Drive
> Nashville, TN 37211
> 866-455-7788 Phone
> 615-834-9923 Fax
>
> www.dieselperformanceparts.com
> _______________________________________________
> fot@autox.team.net
>
> http://www.fot-racing.com
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe: http://autox.team.net/mailman/options/fot/cartravel@pobox.com
_______________________________________________
fot@autox.team.net

http://www.fot-racing.com

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums


<Prev in Thread] Current Thread [Next in Thread>