Search String: Display: Description: Sort:

Results:

References: [ +from:E@ontis.com: 43 ]

Total 43 documents matching your query.

21. traction bars (score: 1)
Author: "J&E" <J&E@ontis.com>
Date: Mon, 10 Jul 2000 11:24:42 -0600
in normans book he says " when set up properly you can feel them come into play" (the traction bars). How do you set them up? It looks to me like you just bolt them on tight. Also do you leave off t
/html/tigers/2000-07/msg00084.html (6,745 bytes)

22. tach tech tip (score: 1)
Author: "J&E" <J&E@ontis.com>
Date: Mon, 10 Jul 2000 15:58:54 -0600
I just completed tom halls tech tip on my mk1a tach. Previously it had no movement. I have a ford electronic ignition in the car. i get movement now but can't quite adjust the dashpot low enough. It
/html/tigers/2000-07/msg00086.html (6,606 bytes)

23. tach (score: 1)
Author: "J&E" <J&E@ontis.com>
Date: Mon, 10 Jul 2000 16:56:37 -0600
my pickup wire was in fact laying on top of spark plug wires. I was just jumpering it to test it. I will hook up inside the car tonire and try again. Thanks steve B382001622
/html/tigers/2000-07/msg00088.html (6,125 bytes)

24. traction bars (score: 1)
Author: "J&E" <J&E@ontis.com>
Date: Mon, 10 Jul 2000 18:44:17 -0600
Sorry, but you missed on this one. Because there is a pivot at the point of axle attachment ,if the clamp at the front is not tight it will just slide up the spring and do nothing. Right? The normal
/html/tigers/2000-07/msg00090.html (6,816 bytes)

25. Fw: tiger clutch dosn't feel right (score: 1)
Author: "J&E" <J&E@ontis.com>
Date: Tue, 11 Jul 2000 17:10:48 -0600
inch clutch. It required too much throw. I installed one of cats masters (dont know if it was smaller or larger) and it made it a just barely workable setup. I just replaced my clutch with a centerfo
/html/tigers/2000-07/msg00098.html (8,084 bytes)

26. vac line (score: 1)
Author: "J&E" <J&E@ontis.com>
Date: Fri, 28 Jul 2000 14:46:38 -0600
I am in need of a vac line from my 7 inch booster in my mk1a to the manifold. This is a steel or alum. pipe that hooks to the brake servo. There is an excellent picture of it in the book of norman o
/html/tigers/2000-07/msg00170.html (6,224 bytes)

27. Fw: vac connector (score: 1)
Author: "J&E" <J&E@ontis.com>
Date: Fri, 28 Jul 2000 10:39:14 -0600
listers I am in need of a vacuum connection pipe for my mk1a with a 7 inch booster. Just like the one on page 152 in the book of norman. Ay help would be appreciated. thanks. steve k b382001622
/html/tigers/2000-07/msg00171.html (6,634 bytes)

28. diffs (score: 1)
Author: "steve" <J&E@ontis.com>
Date: Sat, 11 Sep 1999 17:13:17 -0600
how many splines do tigers have on rear axles? will my dana 44 posi fron a 1967 ford f100 fit right in? steve kenyon B382001622
/html/tigers/1999-09/msg00146.html (6,257 bytes)

29. diffs in f100 (score: 1)
Author: "steve" <J&E@ontis.com>
Date: Sun, 12 Sep 1999 00:02:29 -0600
yes, a dana44 posi in a 1967 ford f100. i checked with ford ; they put them in in 66 and 67. the cover is right and the diff tag. ford says it is a dana 44.3 I removed this diff from my 67 f100 when
/html/tigers/1999-09/msg00149.html (6,323 bytes)

30. diffs (score: 1)
Author: "steve" <J&E@ontis.com>
Date: Sun, 12 Sep 1999 16:40:31 -0600
tag numbers C7TA-L 602909 3.73 there are also 2 different carriers 3.73and lower NUMBERS take one and ALL HIGHER NUMBERS take the other. the difference is the flange where the crown mounts is placed
/html/tigers/1999-09/msg00153.html (6,424 bytes)

31. steering column (score: 1)
Author: "steve" <J&E@ontis.com>
Date: Mon, 13 Sep 1999 20:32:03 -0600
I just did the column in my mk 1A. the shop notes in the supplement by John Crawley are excellent. My bearing cups were stuck solid, but they came out fine with this procedure. The only thing nobody
/html/tigers/1999-09/msg00180.html (6,717 bytes)

32. 091599c (score: 1)
Author: "J&E" <J&E@ontis.com>
Date: Wed, 15 Sep 1999 07:10:51 -0600
measure the distance on each side from the plug inside the diff to the axle housing flange. If it varies more than one eighth inch you may have the wrong carrier. What ratio was on the carrier and w
/html/tigers/1999-09/msg00200.html (6,275 bytes)

33. dana44 (score: 1)
Author: "J&E" <J&E@ontis.com>
Date: Wed, 15 Sep 1999 07:21:37 -0600
I foung a good book listing diffs/splines/shaft dia's. It looks like only older 66-68 jeeps ft or rear list the right spline/dia. My searsh for side gears is not going well. The 4x4 shop says not av
/html/tigers/1999-09/msg00201.html (6,295 bytes)

34. tops (score: 1)
Author: "steve" <J&E@ontis.com>
Date: Sat, 18 Sep 1999 07:11:15 -0600
the peice in question also holds the weather strip. Mine is missing also . I have found a rusty sv alpine for parts. anyone interested in a perfect vinyl dashboard? steve k
/html/tigers/1999-09/msg00268.html (6,375 bytes)

35. re tops (score: 1)
Author: "J&E" <J&E@ontis.com>
Date: Tue, 21 Sep 1999 11:44:03 -0600
the alpine in "tops" isn't here yet. It may be a few weeks yet before i can pick it up. I will let you know as soon as it arrives steve kenyon. B382001622
/html/tigers/1999-09/msg00304.html (6,145 bytes)

36. springs (score: 1)
Author: "J&E" <J&E@ontis.com>
Date: Fri, 24 Sep 1999 07:11:17 -0600
has anyone used CAT front springs?. I have had a bad report on them and I have a set on order. steve k
/html/tigers/1999-09/msg00348.html (6,982 bytes)

37. re ;tops (score: 1)
Author: "J&E" <J&E@ontis.com>
Date: Fri, 24 Sep 1999 10:17:06 -0600
you must have missed my last message to the list. It may be a while (2-3 weeks) before I can get this car. I don't want to make any deals before its here. I thought I would be able to pick it up by
/html/tigers/1999-09/msg00354.html (6,186 bytes)

38. REGISTRY (score: 1)
Author: "J&E" <J&E@ontis.com>
Date: Fri, 24 Sep 1999 15:16:47 -0600
CONTACT NORMAN MILLER AT ROOTS1@BEST.COM HE PREFERS EMAIL RATHER THAN TELEPHONE. SENT HIM A NOTE AND I'M SURE HE WILL GET BACK TO YOU STEVE K
/html/tigers/1999-09/msg00358.html (6,121 bytes)

39. tops (score: 1)
Author: "J&E" <J&E@ontis.com>
Date: Fri, 24 Sep 1999 15:57:46 -0600
alpine sv pretty stripped but excellent dash and guages Also roots radio and brackets (MINE) . no motor or trans. no seats no door panels etc. steve k
/html/tigers/1999-09/msg00359.html (6,321 bytes)

40. diffs (score: 1)
Author: "J&E" <J&E@ontis.com>
Date: Sat, 25 Sep 1999 08:33:02 -0600
I have ordered side gears and ring /pinion from Barry Schonberger. You were right. It was nice to deal with someone who knew exactly what I needed. thanks steve k B382001622
/html/tigers/1999-09/msg00376.html (6,315 bytes)

Current List: 21 - 40
Page: [1] [2] [3]
This search system is powered by Namazu