Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*gaskets\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*gaskets\s*$/: 9 ]

Total 9 documents matching your query.

1. gaskets (score: 1): Author: Unknown; Date: Sun, 11 Mar 2001 15:38:44 -0500; I know that we've gone over this before, but I can't seem to access the archives. For the cork valve cover gasket, should one pre-soak in motor oil, or just smear lithium grease on both surfaces, or; /html/spridgets/2001-03/msg00639.html (7,024 bytes)
2. Re: gaskets (score: 1): Author: Unknown; Date: Sun, 11 Mar 2001 12:49:30 -0800 (PST); Jeff, I just put a tiny bead of RTV on the side that mates to the valve cover, let it setup for a little bit, then bolt it down. never had a leak, and the RTV makes it real clean to pop the cover of; /html/spridgets/2001-03/msg00642.html (7,173 bytes)
3. Re: gaskets (score: 1): Author: Unknown; Date: Sun, 11 Mar 2001 16:00:41 -0500; Thanks, that's what was done this time, but for some reason, massive leaks for no obvious reason. Jeff -- __________________________________________________ Jeffrey H. Boatright, PhD Assistant Profe; /html/spridgets/2001-03/msg00644.html (7,906 bytes)
4. Re: gaskets (score: 1): Author: Unknown; Date: Sun, 11 Mar 2001 13:00:12 -0800; I attach the valve cover side with Copper Permatex gasket sealer. Degrease the valve cover lip so the sealer will stick properly. and let it set up for about an hour before putting it on (check dire; /html/spridgets/2001-03/msg00645.html (8,455 bytes)
5. Re: gaskets (score: 1): Author: Unknown; Date: Sun, 11 Mar 2001 18:18:52 -0500; Could have possibly overtightened the bolts squashing the valve cover? Wanna see one? -- Frank Clarici Toms River, NJ Just Enough Sprites Again http://www.exit109.com/~spritenut; /html/spridgets/2001-03/msg00665.html (7,556 bytes)
6. Re: gaskets (score: 1): Author: Unknown; Date: Sun, 11 Mar 2001 19:13:57 EST; I use black RTV to seal it to the cover. Lrt it dry one day. Then come in and coat the inner edge and head mating surface of the gsaket with the RTV. Let dry one day. When you install this integral; /html/spridgets/2001-03/msg00670.html (7,018 bytes)
7. Re: gaskets (score: 1): Author: Unknown; Date: Sun, 11 Mar 2001 20:55:45 -0500; Also check out that the gasket lines up properly with the cover and DON'T overtighten, Makes the cover into funny mating surfaces! Paul A Re: Re: gaskets Ron, Thanks, that's what was done this time,; /html/spridgets/2001-03/msg00688.html (8,943 bytes)
8. Re: gaskets (score: 1): Author: Unknown; Date: Wed, 14 Mar 2001 23:03:00 -0500; I use RTV on the valve cover-to-gasket joint and nothing on the gasket-to-head joint as suggested by many listers. But I have nicked up the surface of the head where the gasket mates to it with a ch; /html/spridgets/2001-03/msg00870.html (7,846 bytes)
9. Re: gaskets (score: 1): Author: Unknown; Date: Thu, 15 Mar 2001 09:37:12 -0500; Talk about trashing the holy grail of motor mechanics (_!_) Mike L. 60A,67E,59bug -- Original Message -- From Bob Spruck <bspruck at mindspring.com> nicked up the making a /// /// (If they are dupes,; /html/spridgets/2001-03/msg00876.html (7,220 bytes)

Current List: 1 - 9
Page: [1]