- 1. Re: SU Carb -- Float Leaking (score: 1)
- Author: Mark van der Linden <MARK.VANDERLINDEN@ey.com>
- Date: Wed, 1 Jul 1998 15:21:07 -0500
- In your memo you mentioned: "Also, you can remove the aluminum deflector over the overflow hole, and insert a small brass rod." Could you please elaborate on that a little bit (especialy on the alum
- /html/spridgets/1998-07/msg00011.html (11,387 bytes)
- 2. Re: adding additional gauges/What Lucas won't tell you. (score: 1)
- Author: Mark van der Linden <MARK.VANDERLINDEN@ey.com>
- Date: Wed, 1 Jul 1998 16:31:43 -0500
- As promised, hereunder a scanned version of the article you send me: I am aware it is a little bit blurry, but some people may still be able to read it. Sorry for the poor quality, but a fax and a sc
- /html/spridgets/1998-07/msg00017.html (7,259 bytes)
- 3. RE: Chinese junk and being PC (score: 1)
- Author: Mark van der Linden <MARK.VANDERLINDEN@ey.com>
- Date: Thu, 2 Jul 1998 10:52:36 -0500
- Being from Europe I have found out that being Politically Correct has taken a huge flight in the USA, and in my opinion, not for the better. For fear of being called discriminatory, and where it seem
- /html/spridgets/1998-07/msg00055.html (11,986 bytes)
- 4. Re: Chinese junk and being PC (score: 1)
- Author: Mark van der Linden <MARK.VANDERLINDEN@ey.com>
- Date: Thu, 2 Jul 1998 13:44:15 -0500
- Hi Mr. Boicey Yes You're right. You CAN start emailing whomever you want whatever you want and claim to speak for the list? Nobody has the ability to stop you (at least not in the act itself). Keyque
- /html/spridgets/1998-07/msg00085.html (10,566 bytes)
- 5. split gauge (score: 1)
- Author: Mark van der Linden <MARK.VANDERLINDEN@ey.com>
- Date: Fri, 26 Jun 1998 10:42:34 -0500
- I am very interested in that article, and was wondering if you could maybe provide it to me (by fax or so). I will be in the office until July 2nd, and if you maybe would be able to get it to me pri
- /html/spridgets/1998-06/msg00757.html (8,886 bytes)
- 6. Re: Front End Progress/Question (score: 1)
- Author: Mark van der Linden <MARK.VANDERLINDEN@ey.com>
- Date: Fri, 26 Jun 1998 10:53:00 -0500
- Ulix is right. There has been some extensive discussions on the brake fluid and I think I have a printed overview in my Sprite binder. If you want I can look it up and send it to you, or just take ou
- /html/spridgets/1998-06/msg00758.html (8,702 bytes)
- 7. Re: Clutch release bearing (score: 1)
- Author: Mark van der Linden <MARK.VANDERLINDEN@ey.com>
- Date: Fri, 26 Jun 1998 11:39:54 -0500
- I am fairly new to this and do not know whether your technique already has been 'broadcasted' on the web or not, but if it is an alternative to the ezebleed, could you have some time to fill me in?
- /html/spridgets/1998-06/msg00761.html (8,134 bytes)
- 8. RE: SU Carb -- Float Leaking (score: 1)
- Author: Mark van der Linden <MARK.VANDERLINDEN@ey.com>
- Date: Mon, 29 Jun 1998 12:57:15 -0500
- I was recommended to replace the whole with grose jet (see middle section of last Moss edition (green special deals part)). Any one has done this yet? Mark Check or replace your needle valve in the f
- /html/spridgets/1998-06/msg00817.html (8,969 bytes)
- 9. Re: 72 Midget Shift Knob (score: 1)
- Author: Mark van der Linden <MARK.VANDERLINDEN@ey.com>
- Date: Mon, 29 Jun 1998 13:13:22 -0500
- Hi ChucK: In my other car I once had a wooden stick shift knob. However, the lever was to thin. I than decided to use one of those plastic plugs (in Europe we use them after you drill a hole in the w
- /html/spridgets/1998-06/msg00818.html (8,180 bytes)
This search system is powered by
Namazu