Search String: Display: Description: Sort:

Results:

References: [ +from:vscjohn@iamerica.net: 29 ]

Total 29 documents matching your query.

21. Re: Loc-Tite vs. Anti-Sieze (score: 1)
Author: Susan and John Roper <vscjohn@iamerica.net>
Date: Fri, 01 May 1998 14:25:13 -0500
Nils, I don't mean to be testy, and perhaps we don't disagree. My experience, and I have been aroung a long time, is that studs break not because of fatigue, but becaues of poor metallurgy(Italian st
/html/shop-talk/1998-05/msg00003.html (11,167 bytes)

22. Re: Anti-Sieze (score: 1)
Author: Susan and John Roper <vscjohn@iamerica.net>
Date: Mon, 04 May 1998 21:03:01 -0500
Oiled fasteners will not give a exact torque reading, nor will antiseize which is comprised of small beads in a lube. Some fastener manufacturers, ARP comes to mind, offer a lube designed to give acc
/html/shop-talk/1998-05/msg00019.html (8,206 bytes)

23. Re: Anti-Sieze (score: 1)
Author: Susan and John Roper <vscjohn@iamerica.net>
Date: Tue, 05 May 1998 13:29:16 -0500
Not at all. Merely seek to point out that if accuracy is a concern, than the lube that you use is important. John
/html/shop-talk/1998-05/msg00030.html (7,700 bytes)

24. Re: shield gas for MIG (score: 1)
Author: Susan and John Roper <vscjohn@iamerica.net>
Date: Mon, 18 May 1998 21:25:02 -0500
I must disagree. You cannot use CO2 to shield aluminum. On mild steel you can use CO2, a mix or Argon. CO2 is cheaper and your setup will be slightly different. I use argon for everything because I n
/html/shop-talk/1998-05/msg00075.html (8,326 bytes)

25. Re: Parts Washer Recommendation (score: 1)
Author: Susan and John Roper <vscjohn@iamerica.net>
Date: Fri, 03 Apr 1998 17:21:12 -0600
I favor varsol which I have used for years. Fairly cheap, cleans fairly well, and is an approved weed killer for disposal. Also, the odor is slight. John Roper
/html/shop-talk/1998-04/msg00009.html (9,081 bytes)

26. Re: Shop Tools (score: 1)
Author: Susan and John Roper <vscjohn@iamerica.net>
Date: Fri, 17 Apr 1998 18:29:47 -0500
Should you need parts or service once Harbor Freight has your money, you might want to practice bending over and kissing your posterior goodbye. John
/html/shop-talk/1998-04/msg00052.html (9,649 bytes)

27. Re: Cheap workbench advice wanted. (score: 1)
Author: Susan and John Roper <vscjohn@iamerica.net>
Date: Fri, 17 Apr 1998 22:39:01 -0500
Masonite makes a good and fairly inexpensive work surface. Screw it down on top of the plywood. John
/html/shop-talk/1998-04/msg00062.html (8,796 bytes)

28. Re: Loc-Tite vs. Anti-Sieze (score: 1)
Author: Susan and John Roper <vscjohn@iamerica.net>
Date: Wed, 29 Apr 1998 21:16:53 -0500
I beg to differ. Have used loctite products for many years. Nuts fixed in place with loctite are easily broken loose. Studs can be double nutted and broken loose, or in the case of thread problems, r
/html/shop-talk/1998-04/msg00147.html (9,515 bytes)

29. Re: Loc-Tite vs. Anti-Sieze (score: 1)
Author: Susan and John Roper <vscjohn@iamerica.net>
Date: Thu, 30 Apr 1998 18:34:01 -0500
Again, I beg to differ. The issue under discussion was the use of thread locker in installing replacement studs, after the broken stud had been removed. The representation was made that loctite would
/html/shop-talk/1998-04/msg00153.html (9,400 bytes)

Current List: 21 - 29
Page: [1] [2]
This search system is powered by Namazu