- 61. Re: hydraulic floor jack problem (score: 1)
- Author: Dave & Marlene <rusd@velocitus.net>
- Date: Thu, 07 Nov 2002 20:21:19 -0700
- My jack has been leaking a bit for 15 years. I just top it up with jack oil once in a while. Still works fine. Not worth the trouble to rebuild it. Dave Russell /// unsubscribe/change address reques
- /html/shop-talk/2002-11/msg00082.html (7,733 bytes)
- 62. Re: Copper gaskets (score: 1)
- Author: Dave & Marlene <rusd@velocitus.net>
- Date: Thu, 14 Nov 2002 15:00:23 -0700
- To anneal (soften) copper, heat to a dull red & let cool. Doubt if you can get it hot enough in the oven. Range burners or a torch or both may be needed if the part is large. Obviously, don't get it
- /html/shop-talk/2002-11/msg00132.html (8,195 bytes)
- 63. Re: Drill Press recommendations? (score: 1)
- Author: Dave & Marlene <rusd@velocitus.net>
- Date: Sun, 27 Oct 2002 08:01:01 -0700
- Since you want an excuse to get a new drill press, this may not be what you want to hear. It is surprisingly easy to straighten the spindle on most presses. Set up a dial indicator to measure spindl
- /html/shop-talk/2002-10/msg00164.html (8,755 bytes)
- 64. Re: Drill Presses, #2 (score: 1)
- Author: Dave & Marlene <rusd@velocitus.net>
- Date: Mon, 28 Oct 2002 13:05:00 -0700
- I have a two hp mill drill which runs on 120 vac. If you get a "sturdy" mill drill you can do some pretty heavy duty milling & it makes a super drill press. You need to get one which has about a 8"
- /html/shop-talk/2002-10/msg00170.html (9,742 bytes)
- 65. Re: Need a weatherproof stair landing height increaser (score: 1)
- Author: Dave & M <rusd@velocitus.net>
- Date: Tue, 14 Mar 2006 16:35:45 -0700
- Hi Jim, Not sure what you are describing here. If you wish to cap the concrete to raise certain areas, it wouldn't be hard to form the areas & apply a thin mortar cap. Prep the area to be capped by r
- /html/shop-talk/2006-03/msg00073.html (8,737 bytes)
- 66. Re: wire pull info (score: 1)
- Author: Dave & M <rusd@velocitus.net>
- Date: Mon, 20 Mar 2006 02:32:11 -0700
- Hi John, Couple of suggestions. Attach the ends of the wires securely to the end of a sturdy "fish tape" inserted from the pulling end. Strip the wire ends, bend them into a U, fold them over the fis
- /html/shop-talk/2006-03/msg00107.html (8,096 bytes)
- 67. Re: air grease gun tube (score: 1)
- Author: Dave & M <rusd@velocitus.net>
- Date: Mon, 25 Dec 2006 09:32:12 -0700
- Hi Ron, The air powered model supplies about the same actual pressure to the grease as the leveraged mechanical pump linkage would. Any of the standard fittings, hoses, etc. should work just fine. I
- /html/shop-talk/2006-12/msg00155.html (7,795 bytes)
- 68. Re: Searching for past posts (score: 1)
- Author: Dave & M <rusd@velocitus.net>
- Date: Mon, 08 Jan 2007 13:51:53 -0700
- Hi Wayne, It's easier than that. Go here: http://www.team.net/archive/ Click on shop talk, enter your search terms & it's there. Regards, Dave Russell
- /html/shop-talk/2007-01/msg00134.html (7,729 bytes)
- 69. Re: An off-topic question.... (score: 1)
- Author: Dave & M <rusd@velocitus.net>
- Date: Thu, 18 Jan 2007 21:41:27 -0700
- Hi Jim, You get the data in bits & pieces until it is fully down loaded to your computer. If you are viewing the video while it is down loading, it may start - stop - restart - stop etc in the middle
- /html/shop-talk/2007-01/msg00229.html (10,031 bytes)
- 70. Re: Best way to store small engine (score: 1)
- Author: Dave & M <rusd@velocitus.net>
- Date: Sun, 28 Jan 2007 13:31:48 -0700
- Number three. Dave Russell
- /html/shop-talk/2007-01/msg00264.html (8,121 bytes)
This search system is powered by
Namazu