Search String: Display: Description: Sort:

Results:

References: [ +from:jibjib@att.net: 244 ]

Total 244 documents matching your query.

181. Re: [Shop-talk] the air saga continues (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Wed, 1 Jun 2011 22:08:58 -0700
I don't always drain my compressor as frequently as I should, but when I changed out the anode in my hot water heater, I had to cut off about 6 inches, or cut a hole in the ceiling to get it in the t
/html/shop-talk/2011-06/msg00025.html (8,297 bytes)

182. Re: [Shop-talk] anode rods-- was the air saga continues (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Thu, 2 Jun 2011 17:27:58 -0700
Anodes: Just be sure that your anode is a simple bolt type. My Bradford-White anode is integrated into the hot water outlet pipe. The manufacturer got me to a mail order supply house that was reasona
/html/shop-talk/2011-06/msg00040.html (8,665 bytes)

183. Re: [Shop-talk] anode rods-- was the air saga continues (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Thu, 2 Jun 2011 20:27:11 -0700
I agree. Don't stress that sucker. Jack Rich, Very impressive, indeed... I think I would go with the sleeping dogs approach unless your gas bill is very high. I would think you must have several inch
/html/shop-talk/2011-06/msg00044.html (9,964 bytes)

184. Re: [Shop-talk] anode rods-- was the air saga continues (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Sun, 5 Jun 2011 20:19:03 -0700
I don't know that gas fired water heater technology is allowing the new heaters to use a fraction of the energy. They are pretty low tech. I agree on other technologies can do this. We just upgraded
/html/shop-talk/2011-06/msg00065.html (10,526 bytes)

185. Re: [Shop-talk] gps to find the shop (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Mon, 6 Jun 2011 15:35:04 -0700
Just make sure it has lifetime maps and traffic, if it does traffic. When buying new, the cost for these is a minimal adder. Jack to keep it shop related... sometimes losing my way to the shop I'm co
/html/shop-talk/2011-06/msg00098.html (9,197 bytes)

186. Re: [Shop-talk] hanging bicycles (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Wed, 8 Jun 2011 19:35:25 -0700
I use a large hook for each front wheel. If you alternate the directions the bikes face, you can hang a few in a relatively small space. Jack _______________________________________________ Shop-talk
/html/shop-talk/2011-06/msg00132.html (7,985 bytes)

187. Re: [Shop-talk] stripped screw hole in carb (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Sun, 19 Jun 2011 10:00:30 -0700
+1 for Megasquirt!!! 5 Lucky You! Sounds like a good excuse to go INJECTION! http://www.megasquirt.info/ -wayne (loather of carbs) _______________________________________________ Shop-talk@autox.team
/html/shop-talk/2011-06/msg00174.html (9,003 bytes)

188. [Shop-talk] Pulsing brakes (score: 1)
Author: <jibjib@att.net>
Date: Mon, 20 Jun 2011 22:08:25 -0700
I have an interesting issue puzzling me. My 2006 Chevy Malibu is about ready for brakes, which I will be doing shortly. The biggest issue is a pulsing from the left front wheel. The pulsing is very m
/html/shop-talk/2011-06/msg00188.html (7,179 bytes)

189. Re: [Shop-talk] Pulsing brakes (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Tue, 21 Jun 2011 21:41:56 -0700
Good, it's not just me, but you guys are a bit confused about the downhill part too. I have a dial indicator and a magnetic base, so there are no good tools to acquire on this issue, but I will be ch
/html/shop-talk/2011-06/msg00205.html (7,812 bytes)

190. Re: [Shop-talk] quiet compressor (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Wed, 22 Jun 2011 21:03:32 -0700
I have an airbrush and it's compressor is pretty quiet. You may want to check them out. Jack Hi. I need a compressor for work that will be used in an office/lab type environment. Quiet is what I'm lo
/html/shop-talk/2011-06/msg00225.html (8,818 bytes)

191. Re: [Shop-talk] Pulsing brakes (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Wed, 22 Jun 2011 21:13:50 -0700
The edges of the rotors are not badly corroded. When I do run out on a rotor, I do both sides of the rotor so I kind of have thickness covered, cause I'm going to see some sever run out. I will check
/html/shop-talk/2011-06/msg00226.html (8,557 bytes)

192. Re: [Shop-talk] Pulsing brakes (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Thu, 23 Jun 2011 17:11:19 -0700
Good info on the Brembo's. Jack Yeah, rotors are too cheap these days to mess with turning. I will highly recommend the Brembo OEM replacement rotors you can get from Tire Rack and elsewhere. Really
/html/shop-talk/2011-06/msg00231.html (9,484 bytes)

193. Re: [Shop-talk] Pulsing brakes (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Thu, 23 Jun 2011 19:09:25 -0700
Thanks for even better than Brembo info, as I'll bet they are less expensive. I called tire rack for Akebono pads. They didn't have them in stock and suggested a similar pad at 25% less than the Ake
/html/shop-talk/2011-06/msg00233.html (9,918 bytes)

194. Re: [Shop-talk] Wifi to the garage (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Sat, 2 Jul 2011 13:37:19 -0700
Slightly off topic - Hard wired: There is one other route. I got tired of wireless issues and hard wired the five upstairs rooms and two downstairs room in our house with Gigabit speed connections. I
/html/shop-talk/2011-07/msg00017.html (9,621 bytes)

195. Re: [Shop-talk] Wifi to the garage (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Wed, 6 Jul 2011 22:02:29 -0700
While I am a huge proponent of hard wire vs. wireless, I have a buddy who is an EE working for Boeing. For grins, he set up a pair of coffee can wifi antennas and was able to send and receive over 10
/html/shop-talk/2011-07/msg00046.html (8,249 bytes)

196. Re: [Shop-talk] [Bulk] Natural gas tank-based water heaters? (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Fri, 22 Jul 2011 12:50:42 -0700
I like ones with big sacrificial anodes that are easy to change, so I actually change them every few years. Not really shop-related but... My current water heater is approaching 20 years old so it's
/html/shop-talk/2011-07/msg00127.html (7,958 bytes)

197. Re: [Shop-talk] Pulsing brakes (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Sun, 24 Jul 2011 22:38:15 -0700
Ok, replace the front rotors last weekend and the brakes all the way around. The suspension was tight, with no apparent damaged or worn components. What I did find was a discolored portion on one dis
/html/shop-talk/2011-07/msg00140.html (8,582 bytes)

198. Re: [Shop-talk] Window a/c unit for the garage (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Sat, 6 Aug 2011 16:19:44 -0700
Yes, even without a window, you can frame out a "window" opening to put the unit through any wall. The split system is likely the quietest type of system, but in every brand, you will pay a little m
/html/shop-talk/2011-08/msg00033.html (12,891 bytes)

199. [Shop-talk] SMELLS RE: Recommendations wanted re: used pick-up (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Sat, 13 Aug 2011 08:28:09 -0700
--Original Message-- From: shop-talk-bounces@autox.team.net [mailto:shop-talk-bounces@autox.team.net] On Behalf Of Shannah Miller Sent: Friday, August 12, 2011 10:58 PM To: Steve Hammatt Mount Vernon
/html/shop-talk/2011-08/msg00075.html (7,423 bytes)

200. Re: [Shop-talk] Vintique Inc 3rd Brake Light (score: 1)
Author: "Jack Brooks" <jibjib@att.net>
Date: Sat, 5 Nov 2011 21:26:32 -0700
Using the lamp in a TR6's electrical system will provide more robust test than testing off the car, so the voltage variances in the TR6 may have caused an issue. A lot of lower line LED lamps are bu
/html/shop-talk/2011-11/msg00000.html (8,071 bytes)

Current List: 181 - 200
Page: [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13]
This search system is powered by Namazu