Mail Archive Search: <+from:PARKS@Ithaca.edu>

Results:

References: [ +from:PARKS@Ithaca.edu: 8 ]

Total 8 documents matching your query.

1. RE:atlas lathe (score: 1): Author: PARKS <PARKS@Ithaca.edu>; Date: Thu, 03 Jul 1997 09:04:40 -0400 (EDT); Roger et al, Thanks for the replies on the lathe. The model# is TH54. David Parks@Ithaca.edu; /html/shop-talk/1997-07/msg00023.html (6,533 bytes)
2. Atlas lathe (score: 1): Author: PARKS <PARKS@Ithaca.edu>; Date: Mon, 30 Jun 1997 21:52:40 -0400 (EDT); I have recently received an Atlas bench top lathe. It was made in the 1940's/. Does anyone know a source for a manual for this piece of equipment. I had the model number earlier today but it has gone; /html/shop-talk/1997-06/msg00084.html (6,017 bytes)
3. blast cab (score: 1): Author: PARKS <PARKS@Ithaca.edu>; Date: Sun, 04 May 1997 22:17:25 -0400 (EDT); A friend of mine has a cabinet made by blast it all. I used it extensively to blast most of the parts of the 1970 spitfire that I did a frame-off restoration. It worked very well, except in the most; /html/shop-talk/1997-05/msg00013.html (6,777 bytes)
4. garage plans (score: 1): Author: PARKS <PARKS@Ithaca.edu>; Date: Sat, 31 May 1997 08:21:26 -0400 (EDT); THIS MESSAGE WAS SENT ON 17 MAY Date: 17-MAY-1997 00:15:21.76 To: ggorman Cc: shop-talk redwards fzampa Subj: Re: Reply requested: not set Reply by date: Attachment 1 of 2 -- I built a two car garage; /html/shop-talk/1997-05/msg00109.html (7,155 bytes)
5. re: wire welders (score: 1): Author: PARKS <PARKS@Ithaca.edu>; Date: Mon, 14 Apr 1997 11:19:26 -0400 (EDT); Three years ago I bought a lincoln weld pack for restoring a 1970 triumph spitfire that needed most of its body panels repaired or replaced. I had never welded before and found the lincoln quite easy; /html/shop-talk/1997-04/msg00017.html (7,513 bytes)
6. Re: Plasma cutters (score: 1): Author: PARKS <PARKS@Ithaca.edu>; Date: Fri, 25 Apr 1997 19:37:28 -0400 (EDT); Plasma cutters. A friend of mine has a rather expensive unit by I think it is Lincoln. It cost about 2400.00. I have used it to cut 1/4 alluminum and 10 guage steel. It cuts them like they are butter; /html/shop-talk/1997-04/msg00045.html (6,843 bytes)
7. test message (score: 1): Author: PARKS <PARKS@Ithaca.edu>; Date: Thu, 13 Mar 1997 10:55:07 -0400 (EDT); Sorry to bomb the list with a test message, but I had some address problems last week and I am trying to sort them out without bothering MJB. Also, thanks for all the messages in regards to the gas w; /html/shop-talk/1997-03/msg00092.html (6,316 bytes)
8. Re: Cutting Torch Settings? (score: 1): Author: PARKS <PARKS@Ithaca.edu>; Date: Wed, 19 Mar 1997 11:39:52 -0400 (EDT); Victor has a small booklet that is available free from any dealer that carries their equipment. It has a lot of information about safety practices and setting up the equipment for various kinds of wo; /html/shop-talk/1997-03/msg00117.html (6,824 bytes)

Current List: 1 - 8
Page: [1]