- 1. RE: Phone # for RWS (score: 1)
- Author: "Burstein, Wayne M. x281" <BURSTEIN@genicom.com>
- Date: Tue, 07 Apr 98 09:28:00 EST
- You can reach RWS at 215-945-3834. Tell Bill I said Hi! Wayne Burstein wburstein@genicom.com WDC Region SCCA, ITS #10
- /html/shop-talk/1998-04/msg00026.html (6,435 bytes)
- 2. Re: Air Impact tool rec? (score: 1)
- Author: "Burstein, Wayne M. x281" <BURSTEIN@genicom.com>
- Date: Sun, 11 Jan 98 17:52:00 EST
- About six months ago, I replaced a cheapie 1/2" impact with an IR-231. What a difference in both price and performance! My decision was between the 2131 (plastic housing - 600 ft-lbs torque) and the
- /html/shop-talk/1998-01/msg00029.html (8,412 bytes)
- 3. RE: washing shop towels (score: 1)
- Author: "Burstein, Wayne M. x281" <BURSTEIN@genicom.com>
- Date: Mon, 12 May 97 10:39:00 EST
- I keep a bucket of water with LOTS of dish soap in the garage. Used towels go into the bucket to soak until enough accumulate ( this also alleviates the risk of spontaneous combustion of solvent soa
- /html/shop-talk/1997-05/msg00052.html (8,137 bytes)
- 4. RE: Electric impact wrenches (score: 1)
- Author: "Burstein, Wayne M. x281" <BURSTEIN@genicom.com>
- Date: Thu, 27 Feb 97 16:39:00 EST
- My brother tried one of the Harbor Freight variety. It had significantly less than 200 lb-ft of torque. In fact, it would not remove lug nuts that had just been torqued to 70 lb-ft! Back it went....
- /html/shop-talk/1997-02/msg00083.html (6,612 bytes)
- 5. Re: MIG Welders (score: 1)
- Author: "Burstein, Wayne M. x281" <BURSTEIN@genicom.com>
- Date: Wed, 22 May 96 16:28:00 EST
- You are correct -- the Weld-Pack 100 is a flux core machine that is upgradeable to MIG. I have one that I purchased at a very attractive price of $270 and I also purchased the MIG kit for $85. I hav
- /html/shop-talk/1996-05/msg00018.html (8,304 bytes)
- 6. Re: light - was benches (score: 1)
- Author: "Burstein, Wayne M." <BURSTEIN@genicom.com>
- Date: Thu, 18 Jan 96 11:30:00 EST
- You are probably getting a better ballast when you buy a replacement. My biggest problem with the cheap lights is that they have low quality 50 degree ballasts that flicker, etc. If your shop is not
- /html/shop-talk/1996-01/msg00104.html (7,900 bytes)
- 7. FW: Electrical ducting (score: 1)
- Author: "Burstein, Wayne M." <BURSTEIN@genicom.com>
- Date: Tue, 23 Jan 96 17:20:00 EST
- conduit I just finished the electrical wiring in my garage and am now running copper air lines. If I had to do it again, I would run the air first and bend the conduit around the copper pipe. I am n
- /html/shop-talk/1996-01/msg00130.html (8,958 bytes)
- 8. Re: Shop heaters (score: 1)
- Author: "Burstein, Wayne M." <BURSTEIN@genicom.com>
- Date: Fri, 26 Jan 96 15:08:00 EST
- I recently put a heater in my garage (19'x20'). I was planning on putting in a fairly expensive gas heater that would have required venting exhaust to the outside. While perusing the aisles at Home D
- /html/shop-talk/1996-01/msg00204.html (8,185 bytes)
This search system is powered by
Namazu