- 1. [Healeys] A Different Harness Question (Routing) (score: 205)
- Author: dcorning at ford.com (Corning, Dan (D.C.))
- Date: Fri, 13 Jan 2017 22:44:10 +0000
- I purchased the correct harness for my 62 BT7 Tri-Carb. I also purchased Prospero's wiring diagram for the car. Question: Does anyone have any references regarding the proper harness routing for the
- /html/fot/2017-01/msg00318.html (7,412 bytes)
- 2. [Healeys] Smith Gauges - Sceliphrons Love Them! (score: 205)
- Author: dcorning at ford.com (Corning, Dan (D.C.))
- Date: Sat, 18 Feb 2017 20:22:45 +0000
- I wanted to clean my speedometer before installing it in the dash. Removing the bezel and glass, I carefully wiped the face of the gauge and noticed the needle was stuck. Thinking I'll have to send i
- /html/fot/2017-02/msg00234.html (8,241 bytes)
- 3. [Healeys] Correct Solenoid For Car (score: 205)
- Author: dcorning at ford.com (Corning, Dan (D.C.))
- Date: Tue, 21 Feb 2017 20:39:09 +0000
- My baskets full of random Healey parts came with what I think is 3 starter solenoids. Two of the cylindrical ones and one of the square type. For a 1962 BT7 Tri-Carb, which is correct? [cid:image003.
- /html/fot/2017-02/msg00288.html (7,602 bytes)
- 4. [Healeys] Flasher relay advice please (score: 205)
- Author: dcorning at ford.com (Corning, Dan (D.C.))
- Date: Sat, 25 Feb 2017 03:29:05 +0000
- My flasher was having trouble and flashing too fast on one side. I went to O'Rileys auto parts, bought a Novita EL12 flasher and swapped the guts into the Lucas can. Took my time opening the cans, fi
- /html/fot/2017-02/msg00322.html (10,991 bytes)
- 5. [Healeys] Smiths Gauge Oil / Temp Gauge Sensor (score: 205)
- Author: dcorning at ford.com (Corning, Dan (D.C.))
- Date: Mon, 20 Mar 2017 12:12:55 +0000
- I recently purchased a replacement Smiths Gauge Oil / Temp Gauge. The gauge was shipped loose in the box and the sensor wire was bent at 90 degrees during shipment. If I bend the wire back would it l
- /html/fot/2017-03/msg00286.html (7,790 bytes)
- 6. [Healeys] One Missing Screw - Car / Body Number Plate (score: 205)
- Author: dcorning at ford.com (Corning, Dan (D.C.))
- Date: Mon, 10 Apr 2017 22:59:23 +0000
- Unfortunately, I only have 3 of the 4 required screws to attach my ID plates. Does anyone know of a source to find one? If not, anyone have experience with using a replacement screw with the same loo
- /html/fot/2017-04/msg00147.html (8,366 bytes)
- 7. [Healeys] Replacing Hypoid Axle Grease Seal (score: 205)
- Author: dcorning at ford.com (Corning, Dan (D.C.))
- Date: Wed, 26 Apr 2017 22:24:26 +0000
- I am trying to remove the rear axle hub and wheel bearing to replace the oil seal located behind them. After removing the axle shaft, retaining nut and lock washer, the photo shows the hub and bearin
- /html/fot/2017-04/msg00318.html (8,349 bytes)
This search system is powered by
Namazu