--===============2694400163590180379==
--0000000000002f29e505ae0dac5b
I have a question concerning the retention capability of either system. I
have had a chronic issue retaining the soft top at the base of the lock
pillar (B pillar) on my Spit bodied GT6. After dealing with the non
retention of the snap at this location for the past 25+ years, I'm ready to
fix the issue. I have replaced both halves of the stock snap several times
with no improvement. Discounting originality (since neither system is
correct for my car, and there is already a whole lot of non stock with
respect to my car), which retention system Tenax (pull head away from
surface to release,
https://external-content.duckduckgo.com/iu/?u=https%3A%2F%2Ftse3.mm.bing.net%2Fth%3Fid%3DOIP.3AtTYQy0GXTf-EP8MyoN2AAAAA%26pid%3DApi&f=1
) or Lift-a-Dot (rotate retainer away from surface to release,
https://external-content.duckduckgo.com/iu/?u=https%3A%2F%2Ftse1.mm.bing.net%2Fth%3Fid%3DOIP.Zu5yJ5eSoEK-5l8H6OJGYgHaHa%26pid%3DApi&f=1
) do you prefer - and why? TIA, off in digest mode.
--0000000000002f29e505ae0dac5b
Content-Transfer-Encoding: quoted-printable
<div dir=3D"ltr">I have a question concerning the retention capability of e=
ither system.=C2=A0 I have had a chronic issue retaining the soft top at th=
e base of the lock pillar (B pillar) on my Spit bodied GT6.=C2=A0 After dea=
ling with the non retention of the snap at this location for the past 25+ y=
ears, I'm ready to fix the issue.=C2=A0 I have replaced both halves of =
the stock snap several times with no improvement.=C2=A0 Discounting origina=
lity (since neither system is correct for my car, and there is already a wh=
ole lot of non stock with respect to my car), which retention system Tenax =
(pull head away from surface to release,=C2=A0 <a href=3D"https://external-=
content.duckduckgo.com/iu/?u=3Dhttps%3A%2F%2Ftse3.mm.bing.net%2Fth%3Fid%3DO=
IP.3AtTYQy0GXTf-EP8MyoN2AAAAA%26pid%3DApi&f=3D1">https://external-conte=
nt.duckduckgo.com/iu/?u=3Dhttps%3A%2F%2Ftse3.mm.bing.net%2Fth%3Fid%3DOIP.3A=
tTYQy0GXTf-EP8MyoN2AAAAA%26pid%3DApi&f=3D1</a> ) or Lift-a-Dot (rotate =
retainer away from surface to release,=C2=A0 <a href=3D"https://external-co=
ntent.duckduckgo.com/iu/?u=3Dhttps%3A%2F%2Ftse1.mm.bing.net%2Fth%3Fid%3DOIP=
.Zu5yJ5eSoEK-5l8H6OJGYgHaHa%26pid%3DApi&f=3D1">https://external-content=
.duckduckgo.com/iu/?u=3Dhttps%3A%2F%2Ftse1.mm.bing.net%2Fth%3Fid%3DOIP.Zu5y=
J5eSoEK-5l8H6OJGYgHaHa%26pid%3DApi&f=3D1</a> ) do you prefer - and why?=
=C2=A0=C2=A0 TIA, off in digest mode.<br></div>
--0000000000002f29e505ae0dac5b--
--===============2694400163590180379==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
** triumphs@autox.team.net **
Archive: http://www.team.net/pipermail/triumphs http://www.team.net/archive
--===============2694400163590180379==--
|