--===============0499397249070457237==
boundary="----=_Part_5661652_1668752726.1574555518959"
------=_Part_5661652_1668752726.1574555518959
Content-Transfer-Encoding: quoted-printable
Hi:
=C2=A0 =C2=A0 My 1966 TR4A=C2=A0 had round motor mounts that i am replacing=
with rectangular mounts.
the new mounts=C2=A0 have a metal u-shaped cradle that covers 3 sides .=C2=
=A0 =C2=A0the ends are open rubber.=C2=A0 =C2=A0 the remaining side is expo=
sed rubber=C2=A0 with a raised but embeded metal bar covered by=C2=A0 the r=
ubber near the surface and holding the bolt.
which side goes up ?=C2=A0 =C2=A0 =C2=A0the moss and rimmer parts books sho=
w the the open rubber side with the "lump" facing up towards the engine.=C2=
=A0 =C2=A0but a photo from moss shows the the opposite: the steel of the cr=
adle contacts at the engine and the open/rubber side sits on the frame.=C2=
=A0
given the above , the two mounting holes in the frame , and the off center =
bolt locations , i figure there are eight ways install=C2=A0 these mounts ?=
=C2=A0 =C2=A0even that ignores the washers.
please help.=C2=A0 =C2=A0 =C2=A0 =C2=A0 fred
------=_Part_5661652_1668752726.1574555518959
Content-Transfer-Encoding: quoted-printable
<html><head></head><body><div class=3D"ydp89414078yahoo-style-wrap" style=
=3D"font-family:Helvetica Neue, Helvetica, Arial, sans-serif;font-size:16px=
;"><div dir=3D"ltr" data-setdir=3D"false">Hi:</div><div dir=3D"ltr" data-se=
tdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"false"> &nbs=
p; My 1966 TR4A had round motor mounts that i am replacing with recta=
ngular mounts.</div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div d=
ir=3D"ltr" data-setdir=3D"false">the new mounts have a metal u-shaped=
cradle that covers 3 sides . the ends are open rubber. &=
nbsp; the remaining side is exposed rubber with a raised but embeded =
metal bar covered by the rubber near the surface and holding the bolt=
.</div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" da=
ta-setdir=3D"false">which side goes up ? the moss and ri=
mmer parts books show the the open rubber side with the "lump" facing up to=
wards the engine. but a photo from moss shows the the opposite:=
the steel of the cradle contacts at the engine and the open/rubber side si=
ts on the frame. </div><div dir=3D"ltr" data-setdir=3D"false"><br></di=
v><div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-se=
tdir=3D"false">given the above , the two mounting holes in the frame , and =
the off center bolt locations , i figure there are eight ways install =
these mounts ? even that ignores the washers.</div><div dir=3D=
"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"false=
">please help. fred</div></div></body></html>
------=_Part_5661652_1668752726.1574555518959--
--===============0499397249070457237==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
** triumphs@autox.team.net **
Archive: http://www.team.net/pipermail/triumphs http://www.team.net/archive
--===============0499397249070457237==--
|