--===============1828317553128994046==
--00000000000036d5dd0587f5c7a5
Content-Transfer-Encoding: quoted-printable
While driving home today I noticed after about 20 mins of sitting in stop
and go traffic, the car seems to be sluggish like there is no go power
under acceleration. The temp. here is about 70 F today
After a two hour stop, I noticed the power is back and the car accelerated
well.
I have a luminition unit sitting next to the relay box inside the car. I
have a ballast. The coil is sitting attached to the manifold.
The coil in the car is a Unipart one and its resistance is about 2.1 ohm
when hot. I will check the resistance tmr. when cold.
I have 2 spare coils, one labeled LUCAS 15C6 and the other no name one made
in Japan. Both the coils show a resistance of about 2 ohms. ( multi meter
was checked against a good known resistor.)
As a test, I installed the Japanese coil and noticed the car starts and
then dies. I can only assume this coil should be used without a ballast.
The LUCAS coil is an old Stag coil. (date =E2=80=9973 or something like thi=
s) It
seems to work OK with my setup. I plan to try this LUCAS coil and see if
the car drives better.
How critical is the resistance if I use my current setup? Should I even try
the old LUCAS coil with the 2 ohm resistance, or should I invest in a new
coil with the correct 1.5 ohm resistance?
Triumph Stag
Sujit
--=20
Sujit Roy
Cupertino, California
https://triumphstagblog.wordpress.com/
--00000000000036d5dd0587f5c7a5
Content-Transfer-Encoding: quoted-printable
<div dir=3D"ltr"><span style=3D"color:rgb(0,0,0);font-family:Verdana,Geneva=
,Arial,helvetica,sans-serif;font-size:11px">While driving home today I noti=
ced after about 20 mins of sitting in stop and go traffic, the car seems to=
be sluggish like there is no go power under acceleration. The temp. here i=
s about 70 F today</span><br style=3D"color:rgb(0,0,0);font-family:Verdana,=
Geneva,Arial,helvetica,sans-serif;font-size:11px"><span style=3D"color:rgb(=
0,0,0);font-family:Verdana,Geneva,Arial,helvetica,sans-serif;font-size:11px=
">After a two hour stop, I noticed the power is back and the car accelerate=
d well.</span><br style=3D"color:rgb(0,0,0);font-family:Verdana,Geneva,Aria=
l,helvetica,sans-serif;font-size:11px"><br style=3D"color:rgb(0,0,0);font-f=
amily:Verdana,Geneva,Arial,helvetica,sans-serif;font-size:11px"><span style=
=3D"color:rgb(0,0,0);font-family:Verdana,Geneva,Arial,helvetica,sans-serif;=
font-size:11px">I have a luminition unit sitting next to the relay box insi=
de the car. I have a ballast. The coil is sitting attached to the manifold.=
=C2=A0</span><br style=3D"color:rgb(0,0,0);font-family:Verdana,Geneva,Arial=
,helvetica,sans-serif;font-size:11px"><span style=3D"color:rgb(0,0,0);font-=
family:Verdana,Geneva,Arial,helvetica,sans-serif;font-size:11px">The coil i=
n the car is a Unipart one and its resistance is about 2.1 ohm when hot. I =
will check the resistance tmr. when cold.</span><br style=3D"color:rgb(0,0,=
0);font-family:Verdana,Geneva,Arial,helvetica,sans-serif;font-size:11px"><b=
r style=3D"color:rgb(0,0,0);font-family:Verdana,Geneva,Arial,helvetica,sans=
-serif;font-size:11px"><br style=3D"color:rgb(0,0,0);font-family:Verdana,Ge=
neva,Arial,helvetica,sans-serif;font-size:11px"><span style=3D"color:rgb(0,=
0,0);font-family:Verdana,Geneva,Arial,helvetica,sans-serif;font-size:11px">=
I have 2 spare coils, one labeled LUCAS 15C6 and the other no name one made=
in Japan. Both the coils show a resistance of about 2 ohms. ( multi meter =
was checked against a good known resistor.)</span><br style=3D"color:rgb(0,=
0,0);font-family:Verdana,Geneva,Arial,helvetica,sans-serif;font-size:11px">=
<br style=3D"color:rgb(0,0,0);font-family:Verdana,Geneva,Arial,helvetica,sa=
ns-serif;font-size:11px"><span style=3D"color:rgb(0,0,0);font-family:Verdan=
a,Geneva,Arial,helvetica,sans-serif;font-size:11px">As a test, I installed =
the Japanese coil and noticed the car starts and then dies. I can only assu=
me this coil should be used without a ballast. The LUCAS coil is an old Sta=
g coil. (date =E2=80=9973 or something like this) It seems to work OK with =
my setup. I plan to try this LUCAS coil and see if the car drives better.</=
span><br style=3D"color:rgb(0,0,0);font-family:Verdana,Geneva,Arial,helveti=
ca,sans-serif;font-size:11px"><br style=3D"color:rgb(0,0,0);font-family:Ver=
dana,Geneva,Arial,helvetica,sans-serif;font-size:11px"><span style=3D"color=
:rgb(0,0,0);font-family:Verdana,Geneva,Arial,helvetica,sans-serif;font-size=
:11px">How critical is the resistance if I use my current setup? Should I e=
ven try the old LUCAS coil with the 2 ohm resistance, or should I invest in=
a new coil with the correct 1.5 ohm resistance?</span><br style=3D"color:r=
gb(0,0,0);font-family:Verdana,Geneva,Arial,helvetica,sans-serif;font-size:1=
1px"><br>Triumph Stag<br style=3D"color:rgb(0,0,0);font-family:Verdana,Gene=
va,Arial,helvetica,sans-serif;font-size:11px"><span style=3D"color:rgb(0,0,=
0);font-family:Verdana,Geneva,Arial,helvetica,sans-serif;font-size:11px">Su=
jit</span>=C2=A0=C2=A0<br clear=3D"all"><div><br></div>-- <br><div dir=3D"l=
tr" class=3D"gmail_signature" data-smartmail=3D"gmail_signature"><div dir=
=3D"ltr"><div>Sujit Roy<br>Cupertino, California</div><div><br><a href=3D"h=
ttps://triumphstagblog.wordpress.com/" target=3D"_blank">https://triumphsta=
gblog.wordpress.com/</a><br><br></div></div></div></div>
--00000000000036d5dd0587f5c7a5--
--===============1828317553128994046==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
** triumphs@autox.team.net **
Archive: http://www.team.net/pipermail/triumphs http://www.team.net/archive
--===============1828317553128994046==--
|