triumphs
[Top] [All Lists]

[Fot] Cams

Subject: [Fot] Cams
From: fubog1 at aol.com (fubog1)
Date: Tue, 17 Jul 2018 13:39:50 -0400
 My pleasure, glad to contribute any of the mostly-worthless knowledge I've 
accumulated from nearly a half-century of screwing around with TRs...


Glen

 

 

-----Original Message-----
From: timmmurphh <timmmurphh at gmail.com>
To: 'fubog1' <fubog1 at aol.com>; rbtr3a <rbtr3a at cox.net>
Cc: fot <fot at Autox.Team.Net>
Sent: Tue, Jul 17, 2018 1:07 pm
Subject: RE: [Fot] Cams



Thanks for your input on that, Glen.   Very helpful and useful advice.
 
Tim
 
From: fubog1 <fubog1 at aol.com> 
Sent: Tuesday, July 17, 2018 12:05 PM
To: timmmurphh at gmail.com; rbtr3a at cox.net
Cc: fot at Autox.Team.Net
Subject: Re: [Fot] Cams
 

Yes, lacking access to a Cam Doc, you can use a set of V or bearing blocks, a 
degree wheel, dial indicator, and a bit of time, checked at 5 cam degrees, 
works fine.

I'm still old school though, I plot them out on graph paper!

That will give you the lobe profile but most folks don't have the full specs on 
the cam, usually just advertised lift and duration.

Since the tip of the lobe usually starts to go away first, a simple lift 
measurement will reveal the worst, best done with a dial indicator cuz some 
(cheap) cams are ground on different base circles.

Generally, ramp wear is unusual if the tip is still OK, although there can be 
exceptions.

 

Glen.

 

 

 

 

-----Original Message-----
From: timmmurphh <timmmurphh at gmail.com>
To: 'fubog1' <fubog1 at aol.com>; rbtr3a <rbtr3a at cox.net>
Sent: Tue, Jul 17, 2018 12:38 pm
Subject: RE: [Fot] Cams


By degreeing the cam using increments of 10 crankshaft degrees (5 camshaft 
degrees) and then plotting the results in Excel, it is possible to get a very 
accurate picture of the profile of the cam.

 

I?ve attached a spreadsheet showing an intake and exhaust lobe comparison two 
years apart of our Kastner G3 cam for reference.

 

Tim Murphy

#317 TR4

 

From: Fot <fot-bounces at autox.team.net> On Behalf Of fubog1 via Fot
Sent: Monday, July 16, 2018 6:31 AM
To: rbtr3a at cox.net; fot at autox.team.net
Subject: Re: [Fot] Cams

 


Generally any obvious wear or pitting would make it unserviceable, but the wear 
isn't always so obvious.


You can measure the lift and compare to spec, that will show any worn lobes, 
but the best way is to find someone who has a "cam doctor". It's a machine that 
sets it up and measures the complete profile.


Usually if there is anything apparent that suggests that there may be problems, 
there are...


 


Glen


 


 


-----Original Message-----
From: rbtr3a--- via Fot <fot at autox.team.net>
To: fot <fot at autox.team.net>
Sent: Sun, Jul 15, 2018 6:47 pm
Subject: [Fot] Cams

How do I determine if a cam is good or bad. If there are any marks on it does 
that make it bad. I do know that two of the lifters has pitting on the surface. 

Ronnie
_______________________________________________
fot at autox.team.net

http://www.fot-racing.com

Archive: http://www.team.net/pipermail/fot




-------------- next part --------------
An HTML attachment was scrubbed...
URL: 
<http://autox.team.net/pipermail/fot/attachments/20180717/33f34b8e/attachment.html>

<Prev in Thread] Current Thread [Next in Thread>