</lurk mode>
Johnnie asked:
> How do you know if your distributor needs to be replaced or rebuilt? I
> have a Lucas 25D installed.
Randall replied
> Hook up a timing light, start the engine, shine the light on the timing
> mark. If it jumps around, the distributor is worn...
Disconnect the vacuum hose from the vacuum capsule and hook up the timing
light sensor on the ignition coil lead so that every spark produced by the
coil will trigger the timing light. Shine the light on the timing mark - if
you see a single mark that moves per the advance curve as you increase
engine rpm, your distributor is in good shape.
If you see two marks that jump back and forth and change the gap between
them erratically, then your upper shaft bushing is worn out. If the marks
move around relative to one another, you're seeing that the timing for #1
relative to its TDC is not the same as the timing for #4 at its TDC because
the shaft wobble is changing the point gap which changes the dwell angle and
the coil firing point at every revolution. It's hard to get a car to run
well when the timing for every cylinder changes each time the points open.
Timing issues from a wobbly shaft can be cured with the installation of
electronic ignition (Crane recommended) but this is only postponing the
inevitable rebuild
If the mark(s) stay in a fixed position between 800 and 4000 rpm, your
mechanical advance is not working. This could be due to frozen weights or
corrosion between the concentric shafts in the mechanical advance mechanism.
This will cause lousy performance above 2000 rpm. You can check for this by
gently twisting the rotor shaft (you may want to remove the rotor itself so
you don't break the plastic key that holds in it a specific position on the
shaft). You should be able to turn it about 10 degrees or so in one
direction against spring tension that returns it to its original position.
If it is firmly locked in place for both clockwise and anti-clockwise
rotation, the concentric rotor shafts are corroded together and will need
attention.
TR4s should see advance starting at 700-900 engine rpm. The tables below
give you the min/max values for mechanical advance in distributor degrees at
distributor rpm when the distributor is on a distributor machine. Multiply
by two for crankshaft degrees and crankshaft rpm when it's on the engine.
The 40xxx number is the Lucas model number that's stamped on the side of the
distributor body.
TR3/4 40698A
Dist Degrees Advance
RPM Min Max
225 0 0
350 0.5 2.5
750 8.5 10.5
2700 13 15
TR4 61-62 40734A
Dist Degrees Advance
RPM Min Max
250 0 0
450 3.5 5.5
1550 11 13
2800 14 16
TR4 61-onward 40795A
Dist Degrees Advance
RPM Min Max
225 0 0
350 0 2
600 5 7
1200 9 11
Use this Excel spreadsheet to print your own advance curve for a variety of
Triumph cars. Each tab in the spreadsheet is a different model distributor
http://www.snic-braaapp.org/media/DistAdvance.xls
If you plot the curve on the chart and you see a straight angled line with
no knee between two separate slopes, then you have incorrect springs inside
the distributor. At rest, you should see two springs under the breaker
point baseplate. One should be made of thin wire and should be tight on its
mounting pins. The second spring should be made of heavier wire and should
be loose on the pins. As RPM increases, the light spring controls the
advance at a steep rate until the pins move apart enough to contact both
ends of the heavy spring. At the point, both spring control the advance at
a shallower slope. On the tables above, this happens at 750, 1550, and 600
distributor rpm, respectively.
The maximum advance is controlled by a cam that will hit one of the spring
pegs at full advance. It should have a number stamped on it to indicate the
maximum number of distributor degrees advance it will allow. You should be
able to see this through the holes in the baseplate. The distributor models
listed in the tables above should have 14, 15, and 10 degree cams,
respectively
With the engine running, put a vacuum gauge on the vacuum hose that you
removed from the distributor vacuum capsule. Vacuum advance capsules should
have a vacuum source that provides zero vacuum with the throttle closed and
increasing vacuum as you open the throttle. Vacuum retard capsules should
have a vacuum source that provides full manifold vacuum with the throttle
closed and quickly decreasing vacuum as you open the throttle. Stromberg
carbs have the retard source near the throttle plate on the bottom of the
carb and the advance source on the top. SU carbs have the advance source on
the bottom since throttle shaft rotates in the opposite direction from
Stromberg carbs. If you get no vacuum at any throttle position, your vacuum
source is plugged or the hose has extra (more than two) holes in it.
Once you've verified you have a good vacuum source, have an assistant hook
it up to the distributor while you check the timing mark with the timing
light. Advance units should be tested at part throttle, retard units at
closed throttle. A Mity-vac usually works better for this test than the
vacuum source on the carb.
Shameless plug:
Come to VTR 2015 in Fontana, Wisconsin from August 11 - 14 where we will
have a vintage Sun distributor machine in action at our Distributor tech
clinic.
http://www.vtr2015.com
Tim Buja - Rockford, IL - 80 TR8, 73 Stag, 72 TR6
VTR 2015 Registrar and Tech Session presenter
<lurk mode>
** triumphs@autox.team.net **
Archive: http://www.team.net/archive
|