Fred:
Thanks. I still don't think this will work with mine. If you look at
MOSS's catalog, page 15, it shows the 2 mills pins going through
what the manual calls the connecting bush. If you notice, the connecting
bush has an offset shaft, the smaller outer diameter is what the bush
rides on and the larger outer diameter is what the shaft goes into. That
larger diameter "lip" to the bush won't go through the hole in the
bearing. So, even if I unscrew the 4 screws holding the plates, the
shaft can't slide through on the passenger side footwell because the
bush won't fit through the center hole of the shaft bearing. If I can
disengage the shaft bearing from the shaft by sliding it toward the
passenger side, the rest is easy. Same with disengaging the pedal
assembly from the connecting bush. The pedal assembly would just
come out into the footwell, leaving me with the bearing, the bearing plates,
and the connecting bush. My problem is that I've drilled that outer mills
pin out on the driver's side and nothing wants to disengage.
It sounds like we have a different set-up? Thanks for the assistance and if you
have any other ideas, let me know (you may hear a scream coming from the
North later this afternoon!).
Scott
Fred Thomas wrote:
> Scott, on my car, I have one pin on each side of the car, it goes through
> what would like a sleeve, they are located right beside the bushings
> retaining cap, if you remove the passenger side, take the 4 screws out of
> each side holding the bushing in, then you can slide the shaft out through
> the drivers foot well, and just angle it around the pedals. You must remove
> the 4 screws from each side of the fire wall, as wheel as the "L" shaped
> bracket that also bolts into the firewall, this holds the shaft-up and in
> place on the passenger side. "FT"
> ----- Original Message -----
> From: suhring <suhring@lancnews.infi.net>
> To: Fred Thomas <vafred@erols.com>
> Cc: Bob Krivenko <krivenkb@pa.net>; John Krause (home) <jktr250@aol.com>
> Sent: Saturday, February 12, 2000 11:09 PM
> Subject: Re: TR3 Pedal Assembly
>
> > Fred:
> >
> > I ended up drilling out the mills pin on the driver's side. Is the peddle
> > assembly
> > permanently attached to the shaft? When you say one on each side, do you
> mean
> > one right next to the driver's side bearing on the end of the bushing and
> one
> > next
> > to the passenger side bushing? Or do you mean one on each side of the
> driver's
> > side bearing? On the passenger side, I can see the one mills pin and then
> the
> > split pin that holds the lever in place. So there are actually two holes
> on the
> > passenger side. Again (sorry, but I am frustrated and want to get this
> right
> > tomorrow),
> > are you saying that the one I drilled out today on the driver's side is
> the only
> > pin?
> >
> > If it is, I still can't extract the shaft from the driver's side because
> the
> > bush is
> > holding the bearing in place and the inner, outer plate and shaft bearing
> > must first be removed before I can pull the pedal shaft out.
> >
> > Any other help or more detailed description would be appreciated.
> >
> > Fred Thomas wrote:
> >
> > > One on each side, on the passenger side, yes right by the bearing, then
> just
> > > slide it out through the drivers foot well, this is aluminum all the way
> > > across, so when you bend it, you can then straighten it back out. It is
> not
> > > a easy job, either removing or replacing those pins. "FT"
> > > ----- Original Message -----
> > > From: suhring <suhring@lancnews.infi.net>
> > > To: triumph mailing list <triumphs@autox.team.net>
> > > Sent: Saturday, February 12, 2000 4:45 PM
> > > Subject: TR3 Pedal Assembly
> > >
> > > >
> > > > Hope all are enjoying their weekend.
> > > >
> > > > I need some help with removing the accelerator pedal assembly. I seem
> to
> > > >
> > > > be at an impasse with separating the pedal assembly from the
> connecting
> > > > bush/pedal shaft. The shop manual shows two mills pins that go
> > > > through the bush. Appears that on holds the pedal assembly and the
> > > > other holds the shaft. I can only find one mills pin, the one that
> holds
> > > > the
> > > > bush to the shaft. Is the other pin hidden by the shaft bearing? I
> even
> > > > removed the bearing housing hoping to expose the other pin by allowing
> > > > me to move the bearing, but no luck. I am really baffled here since I
> > > > can't release the pedal and there seems to be no other mills pin?
> > > >
> > > > Scott Suhring
> > > > Elizabethtown, PA
> > > > '70 TR6
> > > > '59 TR3
> > > >
> >
> >
|