--===============4323951728585301004==
--part1_e649a4.16ca8cde.4573709a_boundary
Content-Transfer-Encoding: quoted-printable
Content-Language: en
If someone can figure the correct gears it sounds like that if they change=
=20
tires they might have to change gears again. That might mean pulling the=
=20
engine and tranny. =20
Close enough is good enough for me:-)
If your speedometer is going to be rebuilt, a decent company will calibrat=
e=20
your speedo to your tires. At least that will be accurate if you don't=
=20
change tires:-)
Mark L
=20
=20
In a message dated 12/2/2016 7:15:18 P.M. Eastern Standard Time, =20
tigers@autox.team.net writes:
=20
Jerry=20
The 16T gear works very well with today=E2=80=99s radial tires which are=
not as=20
tall as the original bias ply tire.=20
Yes you can work back from the tires, gears combo you have to see what is=
=20
needed.=20
Your tire circumference =E2=80=93 ft in a mile =E2=80=93 tire revs / mile=
=E2=80=93 rear axle=20
gears =E2=80=93 engine revs/ mile=20
Engine revs/ mile =E2=80=93 trans gear to speedo cable gear =E2=80=93 rev=
s/ mile at=20
speedo.=20
Ron Fraser=20
=20
=20
From: Jerry Mo Christopherson [mailto:JCMC2006@suddenlink.net]=20
Sent: Friday, December 02, 2016 5:13 PM
To: 'Ron Fraser' <rfraser@bluefrog.com>
Subject: RE: [Tigers] speedo nylon gear
Ya, I was just thinking one could work it backwards, i.e. I have this=20
wheel/tire combo and this rear end ratio so what combination of =E2=80=9C=
gears=E2=80=9D would=20
I need to get close to something that was as =E2=80=9Caccurate=E2=80=9D=
as the original. =20
To me the speedometer is just something relative anyway. If we are all=
=20
having to live with a 16 tooth gear any way we just accept that it=E2=80=
=99s wrong.=20
Jerry=20
=20
=20
From: Ron Fraser [mailto:rfraser@bluefrog.com] =20
Sent: Friday, December 02, 2016 3:01 PM
To: 'Jerry Mo Christopherson'; _CoolVT@aol.com_ (mailto:CoolVT@aol.com)=
;=20
_Rollright@aol.com_ (mailto:Rollright@aol.com) ; _tigers@autox.team.net_=
=20
(mailto:tigers@autox.team.net)=20
Subject: RE: [Tigers] speedo nylon gear
Jerry=20
I think you=E2=80=99re looking at this the wrong way. =20
The different gears and ratios are designed to make the tire sizes of the=
=20
day work fairly accurately with the speedometer.=20
Original 15T to 6T and a 980 revs/ mile speedo needs a tire with a=20
circumference around 75=E2=80=9D=20
Has anyone ever measured the circumference of an Original Tiger Tire to=
=20
verify this calculation?=20
A 16T to 6T with 980 speedo needs a tire C around 70.5=E2=80=9D=20
These are just a mechanical calculation from the speedo to the tire=20
circumference with all the original gear ratios.=20
Sunbeam had other speedos available =E2=80=93 1000 and 1020 revs/ mile an=
d=20
different axle ratios; any of these will change the accuracy of the speed=
o and=20
thus require a different cable gear.=20
It=E2=80=99s probably easier to convert to a GPS speedometer then play wi=
th all=20
these gear ratios if you=E2=80=99re looking for a totally accurate speedo=
.=20
Ron Fraser=20
=20
=20
From: Jerry Mo Christopherson [mailto:JCMC2006@suddenlink.net] =20
Sent: Friday, December 02, 2016 1:31 PM
To: _CoolVT@aol.com_ (mailto:CoolVT@aol.com) ; _rfraser@bluefrog.com_=20
(mailto:rfraser@bluefrog.com) ; _Rollright@aol.com_ (mailto:Rollright@aol.=
com)=20
Subject: RE: [Tigers] speedo nylon gear
This video is very informative, which leads me to this question. Not=20
knowing the number of the drive gear on the Tiger trans, is it possible=
to get=20
a different drive gear to better match the original ratio using the only=
=20
driven gear that is now available (i.e. 16t)?? Just wondering.=20
Jerry Christopherson=20
9473187=20
TAC insp. #58=20
=20
=20
From: Tigers [mailto:tigers-bounces@autox.team.net] On Behalf Of CoolVT--=
-=20
via Tigers
Sent: Thursday, December 01, 2016 2:47 PM
To: _rfraser@bluefrog.com_ (mailto:rfraser@bluefrog.com) ;=20
_Rollright@aol.com_ (mailto:Rollright@aol.com) ; _tigers@Autox.Team.Net_=
=20
(mailto:tigers@Autox.Team.Net)=20
Subject: Re: [Tigers] speedo nylon gear
=20
This tutorial on speedo gears is taken from a Mustang site (sorry I can't=
=20
give the proper credit). It's for Mustangs, but much is the same on a =
=20
Tiger.
=20
Mark L
=20
=20
https://www.youtube.com/watch?v=3DWDQyhhPNyKc&feature=3Dyoutu.be
=20
=20
=20
=20
=20
In a message dated 12/1/2016 2:14:14 P.M. Eastern Standard Time,=20
_tigers@autox.team.net_ (mailto:tigers@autox.team.net) writes:
=20
=20
Jim=20
The original Mk I speedometer cable gear is C3OA-17271-A 15 teeth=20
Mark on the gear is 15R =E2=80=93 pictures are an original 15R gear =E2=
=80=93 very worn.=20
16R is what is available now=20
The different colors are for different teeth count; makes them easy to =
=20
ID.=20
Took me years at work to convince R&D design teams to change the color of=
=20
gears when different gear sets were being evaluated. I hated getting 5=
=20
bags of black gears that I then had to count the teeth.=20
Ron Fraser=20
=20
=20
From: Tigers [mailto:tigers-bounces@autox.team.net] On Behalf Of=20
Rollright--- via Tigers
Sent: Wednesday, November 30, 2016 6:01 PM
To: _tigers@autox.team.net_ (mailto:tigers@autox.team.net)=20
Subject: [Tigers] speedo nylon gear
=20
Hello,
=20
=20
How many teeth does the Tiger speedo gear have and what do the colors=20
mean? =20
=20
=20
Mustangs Unltd. have so many.........
=20
=20
I recall some years back the correct one for a Tiger went out of print.=
=20
Perhaps they are in print again? =20
=20
=20
Jim Armstrong
382002083
Mk 1A
code 86
TAC # 0763
_______________________________________________
_tigers@autox.team.net_ (mailto:tigers@autox.team.net)=20
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe: http://autox.team.net/mailman/options/tigers/coolvt@aol.com
_______________________________________________
tigers@autox.team.net
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe: http://autox.team.net/mailman/options/tigers/coolvt@aol.com
--part1_e649a4.16ca8cde.4573709a_boundary
Content-Transfer-Encoding: quoted-printable
Content-Language: en
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML xmlns:o =3D "urn:schemas-microsoft-com:office:office"><HEAD>
<META content=3D"text/html; charset=3DUTF-8" http-equiv=3DContent-Type>
<META name=3DGENERATOR content=3D"MSHTML 11.00.9600.18283"></HEAD>
<BODY id=3Drole_body style=3D"FONT-SIZE: 12pt; FONT-FAMILY: Arial; COLOR:=
#000000"=20
bottomMargin=3D7 leftMargin=3D7 rightMargin=3D7 topMargin=3D7><FONT id=3Dr=
ole_document=20
color=3D#000000 size=3D3 face=3DArial>
<DIV>If someone can figure the correct gears it sounds like that if they=
change=20
tires they might have to change gears again. That might mean pulling=
the=20
engine and tranny. </DIV>
<DIV> Close enough is good enough for me:-)</DIV>
<DIV>If your speedometer is going to be rebuilt, a decent company will cal=
ibrate=20
your speedo to your tires. At least that will be accurate if you don=
't=20
change tires:-)</DIV>
<DIV>Mark L</DIV>
<DIV> </DIV>
<DIV>
<DIV>In a message dated 12/2/2016 7:15:18 P.M. Eastern Standard Time,=20
tigers@autox.team.net writes:</DIV>
<BLOCKQUOTE=20
style=3D"PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: blue 2px solid"=
><FONT=20
style=3D"BACKGROUND-COLOR: transparent" color=3D#000000 size=3D2 face=3D=
Arial>
<DIV class=3DWordSection1>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>Jerry<o:p><=
/o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>  =
; &=
nbsp;=20
The 16T gear works very well with today=E2=80=99s radial tires which are=
not as tall=20
as the original bias ply tire.<o:p></o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'><o:p> =
</o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>Yes you can=
work=20
back from the tires, gears combo you have to see what is=20
needed.<o:p></o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'><o:p> =
</o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>Your tire=
=20
circumference =E2=80=93 ft in a mile =E2=80=93 tire revs / mile =E2=80=
=93 rear axle gears =E2=80=93 engine=20
revs/ mile<o:p></o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>Engine revs=
/ mile =E2=80=93=20
trans gear to speedo cable gear =E2=80=93 revs/ mile at speedo.<o:p></o:=
p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'><o:p> =
</o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>Ron=20
Fraser<o:p></o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'><o:p> =
</o:p></SPAN></P>
<DIV>
<DIV=20
style=3D"BORDER-TOP: #e1e1e1 1pt solid; BORDER-RIGHT: medium none; BORDE=
R-BOTTOM: medium none; PADDING-BOTTOM: 0in; PADDING-TOP: 3pt; PADDING-LEFT=
: 0in; BORDER-LEFT: medium none; PADDING-RIGHT: 0in">
<P class=3DMsoNormal><B><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>From:</SPAN=
></B><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'> Jerry Mo=
=20
Christopherson [mailto:JCMC2006@suddenlink.net] <BR><B>Sent:</B> Friday,=
=20
December 02, 2016 5:13 PM<BR><B>To:</B> 'Ron Fraser'=20
<rfraser@bluefrog.com><BR><B>Subject:</B> RE: [Tigers] speedo nylo=
n=20
gear<o:p></o:p></SPAN></P></DIV></DIV>
<P class=3DMsoNormal><o:p> </o:p></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: #1f4=
97d'>Ya,=20
I was just thinking one could work it backwards, i.e. I have this wheel/=
tire=20
combo and this rear end ratio so what combination of =E2=80=9Cgears=E2=
=80=9D would I need to=20
get close to something that was as =E2=80=9Caccurate=E2=80=9D as the ori=
ginal. To me the=20
speedometer is just something relative anyway. If we are all havin=
g to=20
live with a 16 tooth gear any way we just accept that it=E2=80=99s=20
wrong.<o:p></o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: #1f4=
97d'><o:p> </o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: #1f4=
97d'>Jerry<o:p></o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: #1f4=
97d'><o:p> </o:p></SPAN></P>
<DIV>
<DIV=20
style=3D"BORDER-TOP: #b5c4df 1pt solid; BORDER-RIGHT: medium none; BORDE=
R-BOTTOM: medium none; PADDING-BOTTOM: 0in; PADDING-TOP: 3pt; PADDING-LEFT=
: 0in; BORDER-LEFT: medium none; PADDING-RIGHT: 0in">
<P class=3DMsoNormal><B><SPAN=20
style=3D'FONT-SIZE: 10pt; FONT-FAMILY: "Tahoma",sans-serif'>From:</SPAN>=
</B><SPAN=20
style=3D'FONT-SIZE: 10pt; FONT-FAMILY: "Tahoma",sans-serif'> Ron Fraser=
[<A=20
title=3Dmailto:rfraser@bluefrog.com=20
href=3D"mailto:rfraser@bluefrog.com";>mailto:rfraser@bluefrog.com</A>]=20
<BR><B>Sent:</B> Friday, December 02, 2016 3:01 PM<BR><B>To:</B> 'Jerry=
Mo=20
Christopherson'; <A title=3Dmailto:CoolVT@aol.com=20
href=3D"mailto:CoolVT@aol.com";>CoolVT@aol.com</A>; <A=20
title=3Dmailto:Rollright@aol.com=20
href=3D"mailto:Rollright@aol.com";>Rollright@aol.com</A>; <A=20
title=3Dmailto:tigers@autox.team.net=20
href=3D"mailto:tigers@autox.team.net";>tigers@autox.team.net</A><BR><B>Su=
bject:</B>=20
RE: [Tigers] speedo nylon gear<o:p></o:p></SPAN></P></DIV></DIV>
<P class=3DMsoNormal><o:p> </o:p></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>Jerry<o:p><=
/o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>  =
; &=
nbsp;=20
I think you=E2=80=99re looking at this the wrong way. <o:p></o:p><=
/SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>The differe=
nt gears=20
and ratios are designed to make the tire sizes of the day work fairly=20
accurately with the speedometer.<o:p></o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'><o:p> =
</o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>Original 15=
T to 6T=20
and a 980 revs/ mile speedo needs a tire with a circumference around=20
75=E2=80=9D<o:p></o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>Has anyone=
ever=20
measured the circumference of an Original Tiger Tire to verify this=20
calculation?<o:p></o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'><o:p> =
</o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>A 16T to 6T=
with=20
980 speedo needs a tire C around 70.5=E2=80=9D<o:p></o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'><o:p> =
</o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>These are=
just a=20
mechanical calculation from the speedo to the tire circumference with al=
l the=20
original gear ratios.<o:p></o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'><o:p> =
</o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>Sunbeam had=
other=20
speedos available =E2=80=93 1000 and 1020 revs/ mile and different axle=
ratios; any of=20
these will change the accuracy of the speedo and thus require a differen=
t=20
cable gear.<o:p></o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'><o:p> =
</o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>It=E2=80=99=
s probably=20
easier to convert to a GPS speedometer then play with all these gear rat=
ios if=20
you=E2=80=99re looking for a totally accurate speedo.<o:p></o:p></SPAN><=
/P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'><o:p> =
</o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>Ron=20
Fraser<o:p></o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'><o:p> =
</o:p></SPAN></P>
<DIV>
<DIV=20
style=3D"BORDER-TOP: #e1e1e1 1pt solid; BORDER-RIGHT: medium none; BORDE=
R-BOTTOM: medium none; PADDING-BOTTOM: 0in; PADDING-TOP: 3pt; PADDING-LEFT=
: 0in; BORDER-LEFT: medium none; PADDING-RIGHT: 0in">
<P class=3DMsoNormal><B><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'>From:</SPAN=
></B><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif'> Jerry Mo=
=20
Christopherson [<A title=3Dmailto:JCMC2006@suddenlink.net=20
href=3D"mailto:JCMC2006@suddenlink.net";>mailto:JCMC2006@suddenlink.net</=
A>]=20
<BR><B>Sent:</B> Friday, December 02, 2016 1:31 PM<BR><B>To:</B> <A=20
title=3Dmailto:CoolVT@aol.com href=3D"mailto:CoolVT@aol.com";>CoolVT@aol.=
com</A>;=20
<A title=3Dmailto:rfraser@bluefrog.com=20
href=3D"mailto:rfraser@bluefrog.com";>rfraser@bluefrog.com</A>; <A=20
title=3Dmailto:Rollright@aol.com=20
href=3D"mailto:Rollright@aol.com";>Rollright@aol.com</A><BR><B>Subject:</=
B> RE:=20
[Tigers] speedo nylon gear<o:p></o:p></SPAN></P></DIV></DIV>
<P class=3DMsoNormal><o:p> </o:p></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: #1f4=
97d'>This=20
video is very informative, which leads me to this question. Not kn=
owing=20
the number of the drive gear on the Tiger trans, is it possible to get=
a=20
different drive gear to better match the original ratio using the only=
driven=20
gear that is now available (i.e. 16t)?? Just=20
wondering.<o:p></o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: #1f4=
97d'><o:p> </o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: #1f4=
97d'>Jerry=20
Christopherson<o:p></o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: #1f4=
97d'>9473187<o:p></o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: #1f4=
97d'>TAC=20
insp. #58<o:p></o:p></SPAN></P>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: #1f4=
97d'><o:p> </o:p></SPAN></P>
<DIV>
<DIV=20
style=3D"BORDER-TOP: #b5c4df 1pt solid; BORDER-RIGHT: medium none; BORDE=
R-BOTTOM: medium none; PADDING-BOTTOM: 0in; PADDING-TOP: 3pt; PADDING-LEFT=
: 0in; BORDER-LEFT: medium none; PADDING-RIGHT: 0in">
<P class=3DMsoNormal><B><SPAN=20
style=3D'FONT-SIZE: 10pt; FONT-FAMILY: "Tahoma",sans-serif'>From:</SPAN>=
</B><SPAN=20
style=3D'FONT-SIZE: 10pt; FONT-FAMILY: "Tahoma",sans-serif'> Tigers [<A=
=20
title=3Dmailto:tigers-bounces@autox.team.net=20
href=3D"mailto:tigers-bounces@autox.team.net";>mailto:tigers-bounces@auto=
x.team.net</A>]=20
<B>On Behalf Of </B>CoolVT--- via Tigers<BR><B>Sent:</B> Thursday, Decem=
ber=20
01, 2016 2:47 PM<BR><B>To:</B> <A title=3Dmailto:rfraser@bluefrog.com=20
href=3D"mailto:rfraser@bluefrog.com";>rfraser@bluefrog.com</A>; <A=20
title=3Dmailto:Rollright@aol.com=20
href=3D"mailto:Rollright@aol.com";>Rollright@aol.com</A>; <A=20
title=3Dmailto:tigers@Autox.Team.Net=20
href=3D"mailto:tigers@Autox.Team.Net";>tigers@Autox.Team.Net</A><BR><B>Su=
bject:</B>=20
Re: [Tigers] speedo nylon gear<o:p></o:p></SPAN></P></DIV></DIV>
<P class=3DMsoNormal><o:p> </o:p></P>
<DIV>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-FAMILY: "Arial",sans-serif; COLOR: black'>This tutorial on=
speedo=20
gears is taken from a Mustang site (sorry I can't give the proper=20
credit). It's for Mustangs, but much is the same on a=20
Tiger.<o:p></o:p></SPAN></P></DIV>
<DIV>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-FAMILY: "Arial",sans-serif; COLOR: black'>Mark=20
L<o:p></o:p></SPAN></P></DIV>
<DIV>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-FAMILY: "Arial",sans-serif; COLOR: black'> <o:p></o:p=
></SPAN></P></DIV>
<DIV>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-FAMILY: "Arial",sans-serif; COLOR: black'><A=20
title=3Dhttps://www.youtube.com/watch?v=3DWDQyhhPNyKc&feature=3Dyout=
u.be=20
href=3D"https://www.youtube.com/watch?v=3DWDQyhhPNyKc&feature=3Dyout=
u.be">https://www.youtube.com/watch?v=3DWDQyhhPNyKc&feature=3Dyoutu.be=
</A><o:p></o:p></SPAN></P></DIV>
<DIV>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-FAMILY: "Arial",sans-serif; COLOR: black'> <o:p></o:p=
></SPAN></P></DIV>
<DIV>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-FAMILY: "Arial",sans-serif; COLOR: black'> <o:p></o:p=
></SPAN></P></DIV>
<DIV>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-FAMILY: "Arial",sans-serif; COLOR: black'> <o:p></o:p=
></SPAN></P></DIV>
<DIV>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-FAMILY: "Arial",sans-serif; COLOR: black'> <o:p></o:p=
></SPAN></P></DIV>
<DIV>
<P class=3DMsoNormal><SPAN=20
style=3D'FONT-FAMILY: "Arial",sans-serif; COLOR: black'>In a message dat=
ed=20
12/1/2016 2:14:14 P.M. Eastern Standard Time, <A=20
title=3Dmailto:tigers@autox.team.net=20
href=3D"mailto:tigers@autox.team.net";>tigers@autox.team.net</A>=20
writes:<o:p></o:p></SPAN></P></DIV>
<DIV>
<BLOCKQUOTE=20
style=3D"MARGIN-BOTTOM: 5pt; BORDER-TOP: medium none; BORDER-RIGHT: medi=
um none; BORDER-BOTTOM: medium none; PADDING-BOTTOM: 0in; PADDING-TOP: 0in=
; PADDING-LEFT: 4pt; MARGIN-LEFT: 3.75pt; BORDER-LEFT: blue 1.5pt solid;=
MARGIN-TOP: 5pt; PADDING-RIGHT: 0in">
<DIV>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: bl=
ack'>Jim<o:p></o:p></SPAN></P>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: bl=
ack'> &nb=
sp; =20
The original Mk I speedometer cable gear is C3OA-17271-A 15=20
teeth<o:p></o:p></SPAN></P>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: bl=
ack'>Mark=20
on the gear is 15R =E2=80=93 pictures are an original 15R gear =E2=80=
=93 very=20
worn.<o:p></o:p></SPAN></P>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: bl=
ack'>16R=20
is what is available now<o:p></o:p></SPAN></P>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: bl=
ack'><o:p> </o:p></SPAN></P>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: bl=
ack'>The=20
different colors are for different teeth count; makes them easy to=20
ID.<o:p></o:p></SPAN></P>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: bl=
ack'>Took=20
me years at work to convince R&D design teams to change the color=
of=20
gears when different gear sets were being evaluated. I hat=
ed=20
getting 5 bags of black gears that I then had to count the=20
teeth.<o:p></o:p></SPAN></P>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: bl=
ack'><o:p> </o:p></SPAN></P>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: bl=
ack'>Ron=20
Fraser<o:p></o:p></SPAN></P>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: bl=
ack'><o:p> </o:p></SPAN></P>
<DIV>
<DIV=20
style=3D"BORDER-TOP: #e1e1e1 1pt solid; BORDER-RIGHT: medium none; BOR=
DER-BOTTOM: medium none; PADDING-BOTTOM: 0in; PADDING-TOP: 3pt; PADDING-LE=
FT: 0in; BORDER-LEFT: medium none; PADDING-RIGHT: 0in">
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><B><SP=
AN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: bl=
ack'>From:</SPAN></B><SPAN=20
style=3D'FONT-SIZE: 11pt; FONT-FAMILY: "Calibri",sans-serif; COLOR: bl=
ack'>=20
Tigers [<A title=3Dmailto:tigers-bounces@autox.team.net=20
href=3D"mailto:tigers-bounces@autox.team.net";>mailto:tigers-bounces@au=
tox.team.net</A>]=20
<B>On Behalf Of </B>Rollright--- via Tigers<BR><B>Sent:</B> Wednesday,=
=20
November 30, 2016 6:01 PM<BR><B>To:</B> <A=20
title=3Dmailto:tigers@autox.team.net=20
href=3D"mailto:tigers@autox.team.net";>tigers@autox.team.net</A><BR><B>=
Subject:</B>=20
[Tigers] speedo nylon gear<o:p></o:p></SPAN></P></DIV></DIV>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D"COLOR: black"><o:p> </o:p></SPAN></P>
<DIV>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 10pt; FONT-FAMILY: "Arial",sans-serif; COLOR: blac=
k'>Hello,<o:p></o:p></SPAN></P></DIV>
<DIV>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 10pt; FONT-FAMILY: "Arial",sans-serif; COLOR: blac=
k'> <o:p></o:p></SPAN></P></DIV>
<DIV>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 10pt; FONT-FAMILY: "Arial",sans-serif; COLOR: blac=
k'>How=20
many teeth does the Tiger speedo gear have and what do the colors mean=
?=20
<o:p></o:p></SPAN></P></DIV>
<DIV>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 10pt; FONT-FAMILY: "Arial",sans-serif; COLOR: blac=
k'> <o:p></o:p></SPAN></P></DIV>
<DIV>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 10pt; FONT-FAMILY: "Arial",sans-serif; COLOR: blac=
k'>Mustangs=20
Unltd. have so many.........<o:p></o:p></SPAN></P></DIV>
<DIV>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 10pt; FONT-FAMILY: "Arial",sans-serif; COLOR: blac=
k'> <o:p></o:p></SPAN></P></DIV>
<DIV>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 10pt; FONT-FAMILY: "Arial",sans-serif; COLOR: blac=
k'>I=20
recall some years back the correct one for a Tiger went out of print.=
=20
Perhaps they are in print again? <o:p></o:p></SPAN></P>
<DIV>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 10pt; FONT-FAMILY: "Arial",sans-serif; COLOR: blac=
k'> <o:p></o:p></SPAN></P></DIV>
<DIV>
<P class=3DMsoNormal=20
style=3D"mso-margin-top-alt: auto; mso-margin-bottom-alt: auto"><SPAN=
=20
style=3D'FONT-SIZE: 10pt; FONT-FAMILY: "Arial",sans-serif; COLOR: blac=
k'>Jim=20
Armstrong<BR>382002083<BR>Mk 1A<BR>code 86<BR>TAC #=20
0763<o:p></o:p></SPAN></P></DIV></DIV></DIV>
<P class=3DMsoNormal style=3D"MARGIN-BOTTOM: 12pt"><SPAN=20
style=3D'FONT-SIZE: 10pt; FONT-FAMILY: "Arial",sans-serif; COLOR: blac=
k'><BR><BR>_______________________________________________<BR><BR><A=20
title=3Dmailto:tigers@autox.team.net=20
href=3D"mailto:tigers@autox.team.net";>tigers@autox.team.net</A><BR><BR=
>Donate:=20
<A title=3Dhttp://www.team.net/donate.html=20
href=3D"http://www.team.net/donate.html";>http://www.team.net/donate.ht=
ml</A><BR>Archive:=20
<A title=3Dhttp://www.team.net/archive=20
href=3D"http://www.team.net/archive";>http://www.team.net/archive</A><B=
R>Forums:=20
<A title=3Dhttp://www.team.net/forums=20
href=3D"http://www.team.net/forums";>http://www.team.net/forums</A><BR>=
Unsubscribe:=20
<A title=3Dhttp://autox.team.net/mailman/options/tigers/coolvt@aol.com=
=20
href=3D"http://autox.team.net/mailman/options/tigers/coolvt@aol.com";>h=
ttp://autox.team.net/mailman/options/tigers/coolvt@aol.com</A></SPAN><SPAN=
=20
style=3D'FONT-FAMILY: "Arial",sans-serif; COLOR: black'><o:p></o:p></S=
PAN></P></BLOCKQUOTE></DIV></DIV><BR><BR>_________________________________=
______________<BR><BR>tigers@autox.team.net<BR><BR>Donate:=20
http://www.team.net/donate.html<BR>Archive:=20
http://www.team.net/archive<BR>Forums:=20
http://www.team.net/forums<BR>Unsubscribe:=20
http://autox.team.net/mailman/options/tigers/coolvt@aol.com<BR><BR><BR><=
/FONT></BLOCKQUOTE></DIV></FONT></BODY></HTML>
--part1_e649a4.16ca8cde.4573709a_boundary--
--===============4323951728585301004==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
tigers@autox.team.net
Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/tigers/mharc@autox.team.net
--===============4323951728585301004==--
|