My car (B9470334LRXFE) had an original wood dash when I got it. The car
was largely original with the original seats, etc. It's possible a
previous owner may have switched in the wood dash in place of a vinyl
one, but, if so, I'd suspect that it wouldn't have made much sense to
swap in the badly cracked and peeling original wood dash, so it would
likely have either been pretty early in the car's history, or original
to the car.
--Alex Haugland
B9470334LRXFE
On 1/25/2015 4:28 PM, Gary via Tigers wrote:
> According to TBON, approximately
> B9470400.
> Gary
>
> Sent from my iPhone
>
>> On Jan 25, 2015, at 3:19 PM, Jeffery Randall <jefferyrandall@gmail.com>
> wrote:
>> Being too lazy to start a new thread, would any of you's guys know what the
> cut off is for vinyl dash on early mk1s. I thought it was 331 but not sure.
> Thanks
>> Jeff
>>
>>> On Sun, Jan 25, 2015 at 12:31 PM, Gary Winblad via Tigers
> <tigers@autox.team.net> wrote:
>>> And I might add..
>>>
>>> B9470622 does have both of these from the factory..
>>> Gary
>>>
>>> ----- Original Message -----
>>> From: Ron Fraser via Tigers <tigers@autox.team.net>
>>> To: awtiger@cox.net, tigers@autox.team.net
>>> Sent: Sun, 25 Jan 2015 16:09:28 -0000 (UTC)
>>> Subject: Re: [Tigers] Need a couple of washers
>>>
>>> Andy
>>> I did not see if you got help with these.
>>>
>>> DC washer = double coil spring washer
>>>
>>> If you Google that name a number of sites pop up and hopefully one of them
>>> sells them.
>>>
>>> Ron Fraser
>>>
>>> -----Original Message-----
>>> From: Tigers [mailto:tigers-bounces@autox.team.net] On Behalf Of
> awtiger---
>>> via Tigers
>>> Sent: Thursday, January 22, 2015 11:56 AM
>>> To: tigers@autox.team.net
>>> Subject: [Tigers] Need a couple of washers
>>>
>>>
>>> Hey, guys:
>>>
>>> Does anyone out there have a couple of what the parts book calls "D.C."
>>> washers (double-coil)? Specifically, I'm looking for the D.C. washer that
>>> goes on the hood prop where it hooks to its swivel point on the car (I
> think
>>> this one is 5/16" in I.D.). Also, isn't there one of these that's
> supposed
>>> to go on the hood latch mechanism under the pull rod slide that keeps the
>>> slide at the correct height? I would swear I've seen them on there before
>>> on Tigers and Alpines but my car didn't have one and I can't find one in
> the
>>> parts book.
>>>
>>> Bottom line is that I am for sure in need of the one that goes on the prop
>>> rod and, if there is supposed to be one on the hood latch mechanism, then
> I
>>> need it as well. As usual, I appreciate any assistance.
>>>
>>> BTW...the engine & trans combo is finally going back in the car on
> Saturday.
>>> Wish me good luck!!!!!
>>>
>>> Thanks,
>>> Andy Walker
>>> Edmond, OK
>>> B382001600LRXFE
>>> TAC #740
>>> _______________________________________________
>>>
>>> tigers@autox.team.net
>>>
>>> Donate: http://www.team.net/donate.html
>>> Archive: http://www.team.net/archive
>>> Forums: http://www.team.net/forums
>>> Unsubscribe:
> http://autox.team.net/mailman/options/tigers/jefferyrandall@gmail.com
> _______________________________________________
>
> tigers@autox.team.net
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe: http://autox.team.net/mailman/options/tigers/ahauglan@gmail.com
_______________________________________________
tigers@autox.team.net
Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/tigers/mharc@autox.team.net
|