I have replaced one in the car. You need to:
Remove radiator
Unbolt and move rack forward or just remove.
Put jack under engine and unbolt motor mounts.
See if you can lift engine high enough without pushing valve covers into
scuttle to gain access to damper. If not then lower engine and remove valve
covers.
The rest is straight out of the book, although you may need to loosen the
oil pan front bolts.
Bugz
On Friday, October 10, 2014, Owain Lloyd <owain.lloyd@gmail.com> wrote:
> If you ever need less than 1/2 inch more clearance to the rad and you have
> the original early timing cover, its worth remembering that the later
> timing covers are thinner. you'll need to use different bolts to attach
> it. i've never tried changing one with the engine still in the car but it
> should be doable with a quality damper puller and the rad removed.
>
> On Thu, Oct 9, 2014 at 4:39 PM, Tom Parker <tkparker1941@gmail.com
> <javascript:;>> wrote:
>
> > Dave,
> >
> > Thanks. The response was from an old post on the forum right after
> Griffin
> > announced the radiator / fan combination. I took a look at my '67 and
> > thought there's no way that'll fit. So I followed up with Benji at
> Griffin.
> > The note was to report back what he found: 1 1/2" radiator core, 2 1/2"
> > fan. No way that'll fit with a motor driven water pump. He said they'd
> sold
> > lots of them. No comment so far from anyone who bought one.
> >
> > My 289 has a recored stock radiator, the shop said it was a "high
> > efficiency" core, @ 2 1/2" thick. The engine's .030 overbore, Edelbrock
> > heads, manifold, cam, Holley carb. and a Summit "wide paddle" flex fan
> and
> > a Summit 10" pusher fan behind the grille a la TEAE's recommendations. At
> > an idle speed @ 675 rpm it will overheat in the Florida heat. I installed
> > the Maverick reduced diameter pump pulley, it seems to help but in
> summer I
> > kick the idle up a bit.
> >
> > Tom
> > '67 Mark 2
> >
> > On Thu, Oct 9, 2014 at 3:40 PM, Dave Munroe <dave@munroe.ca
> <javascript:;>> wrote:
> >
> > > Tom;
> > >
> > > My Tiger has a 2 5/8" thick alloy rad installed with an electric fan
> > > mounted on the forward side of the rad. I have a water pump-mounted fan
> > > that has the blades rearward of the fan mounting flange, so it takes up
> > no
> > > clearance beyond the bolts holding the fan on the flange.
> > >
> > > No overheating issues with this set-up...331ci stroked 289. 317hp/350
> ft
> > > lb torque.
> > >
> > > Photos available if you'd like.
> > >
> > > Dave
> > > B382000450
> > >
> > >
> > >
> > > ----- Original Message ----- From: "Tom Parker" <
> tkparker1941@gmail.com <javascript:;>>
> > > To: <genepadgett@comcast.net <javascript:;>>
> > > Cc: "LIST TIGER" <tigers@autox.team.net <javascript:;>>
> > > Sent: Thursday, October 09, 2014 3:08 PM
> > > Subject: Re: [Tigers] tiger radiator
> > >
> > >
> > >
> > > A little late with this response. Sorry, Gmail issues...
> > >>
> > >> I visited with Benji at Griffin to discuss the new electric fan /
> > radiator
> > >> combo. From their engineering drawings the fan adds another @ 2 1/2"
> on
> > >> the
> > >> engine side of the radiator, My Tiger has less than an inch clearance
> > >> between the tip of the water pump and the radiator core. I suspect
> > that's
> > >> about right, I might be able to finagle another half inch or so by
> > horsing
> > >> the engine back, but no more (and I'm not gonna try it...).
> > >>
> > >> So my impression is the electric fan won't fit with the engine driven
> > >> water
> > >> pump installed. It MAY fit with an electric water pump, but that comes
> > >> with
> > >> issues; the 6 bolt 289 uses a different pump than the 5 bolt 260 /
> 289.
> > I
> > >> haven't looked into electric pumps so I don't know if they're
> available
> > >> for
> > >> the 260.
> > >>
> > >> Tom
> > >> '67 Mark 2
> > _______________________________________________
> >
> > tigers@autox.team.net <javascript:;>
> >
> > Donate: http://www.team.net/donate.html
> > Archive: http://www.team.net/archive
> > Forums: http://www.team.net/forums
> > Unsubscribe:
> > http://autox.team.net/mailman/options/tigers/owain.lloyd@gmail.com
> _______________________________________________
>
> tigers@autox.team.net <javascript:;>
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe:
> http://autox.team.net/mailman/options/tigers/mark44124@gmail.com
_______________________________________________
tigers@autox.team.net
Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/tigers/mharc@autox.team.net
|