Lots of pictures and instructions at
http://tigersunited.com/techtips/SteveLaifmanValance/pt-SteveLaifmanValance1.asp
On Wed, Mar 21, 2012 at 9:52 AM, James Lindner <jliny5@cox.net> wrote:
> Hi All
>
> I would really appreciate if somebody could share with me a photo(s) of
> the locations where you have inserted foam to block gaps. I have the horn
> holes blocked, six blade fan and I am getting ready to install a reduced
> diameter pulley. Blocking the gaps seems like another logical step.
>
> Thanks
>
> Jim
>
> -----Original Message----- From: Smit, Theo
> Sent: Wednesday, March 21, 2012 12:42 PM
> To: CoolVT@aol.com ; tigers@autox.team.net ; dave@munroe.ca
> Subject: Re: [Tigers] Tiger Cooling
>
> Hi Mark,
> I don't think that there are any quick cooling aids for the Tiger - all of
> them require attention to detail to get more than just a marginal benefit.
>
> The Cressida fan is about 12" diameter and has an integrated steel shroud;
> it
> just barely fits below the sheetmetal in the nose. I used foam adhesive
> tape
> to seal the gap between the rad matrix and the shroud. The problem you
> always
> have with pusher fans is that the motor obscures some of the available
> area; a
> second thing is that if the gaps aren't filled, then the air can just go
> out
> the side rather than through the radiator. The reason why I used this fan
> is
> that it was evidently designed from the outset as a pusher application. A
> lot
> of aftermarket fans are designed as a puller, and then when they're used
> in a
> pusher application they really don't move anywhere near the air that
> they're
> supposedly rated at.
>
> The only thing that would be nice is to have a similar fan, but larger, so
> that it would move more air over more of the radiator. You'd end up with
> part
> of the fan output deadheading against the lower radiator support though.
>
> Moving air through half the rad should be more than sufficient, since the
> fan
> is only required to boost airflow at low speeds. You just have to make sure
> that the air you're moving is really going through the rad rather than
> around
> it, and that it's moving with sufficient speed.
> A secondary issue is that if the fan only covers part of the radiator core,
> are those core tubes actually flowing enough coolant to do the job?
>
> Theo
>
> ______________________________**__
> This e-mail and any attachments may contain confidential material for the
> sole
> use of the intended recipient. If you are not the intended recipient,
> please
> be aware that any disclosure, copying, distribution or use of this e-mail
> or
> any attachment is prohibited. If you have received this e-mail in error,
> please contact the sender and delete all copies.
>
> Thank you for your cooperation.
> ______________________________**_________________
>
> tigers@autox.team.net
>
> Donate: http://www.team.net/donate.**html<http://www.team.net/donate.html>
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe:
> http://autox.team.net/mailman/**options/tigers/jliny5@cox.net<http://autox.team.net/mailman/options/tigers/jliny5@cox.net>
> ______________________________**_________________
>
> tigers@autox.team.net
>
> Donate: http://www.team.net/donate.**html<http://www.team.net/donate.html>
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe: http://autox.team.net/mailman/**options/tigers/jay.laifman@**
> gmail.com<http://autox.team.net/mailman/options/tigers/jay.laifman@gmail.com>
_______________________________________________
tigers@autox.team.net
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe:
http://autox.team.net/mailman/options/tigers/tigers-archive@autox.team.net
|