Well the one that was on teh 302 I picked up definitely has the square
but the dip stick certainly had nothing to do with that. Instead, there
is a small threaded boss lower down that the tang or bracket on the
dipstick fastened to. Same place where my Tiger stick was fastened.
mayf
______________________________
drmayf
Worlds Fastest Sunbeam, period.
204.913 mph flying mile
210.779 mph exit speed
On 9/10/2011 12:52 PM, Kirk Smith wrote:
> I might be stating the obvious, but the standard Ford generator bracket has
> a rectangle or square (depending on year) opening cut in it to facilitate
> the dipstick. The Tiger generator bracket has no such hole, with the
> dipstick attached to the front of the Tiger generator bracket.
>
> Kirk
>
> -----Original Message-----
> From: tigers-bounces@autox.team.net [mailto:tigers-bounces@autox.team.net]
> On Behalf Of Ron Fraser
> Sent: Saturday, September 10, 2011 5:11 AM
> To: 'RObin Young'; genepadgett@comcast.net
> Cc: harryb@elams.org; tigers@autox.team.net
> Subject: Re: [Tigers] Generator bracket
>
> Robin
> I don't think there is any confusion; we are just seeking
> information about this part.
>
> I have stated the Tiger generator bracket was ordered by the Ford
> Industrial Division and carries a C4JZ part number in the Parts List. It
> is a Tiger specific part with no casting number. The offset is different
> from the stock Ford part to line up the fan belt on the Tiger 260 engine.
> The pulleys on the Tiger 260 engine also carry a C4JZ part number which
> makes them Tiger specific too.
>
> This does not mean that a stock Ford Generator bracket could not
> work but you would need to space the generator to the rear around 3/4" to
> line up the fan belt. You would also need to look for any hood clearance
> issues with the stock Ford bracket.
>
> The casting number for the stock Ford generator bracket is C2OE-10039-H. If
> anyone has a casting number on their Tiger generator bracket; I just ask
> that you report the full number and I will investigate that number as best
> I'm able.
>
> Ron Fraser
>
> -----Original Message-----
> From: RObin Young [mailto:robin02@mindspring.com]
> Sent: Friday, September 09, 2011 8:23 PM
> To: genepadgett@comcast.net; rfraser@bluefrog.com
> Cc: harryb@elams.org; tigers@autox.team.net
> Subject: RE: [Tigers] Generator bracket
>
>
> Ron, to further add to the confusion.....the bracket off B9471769 has only
> a triangle and a 2 stamped on it. Over the last couple of days, I dipped it
> and cleaned many coats of black paint off to find what appears to be a sand
> cast texture with no other marks. Robin Young
> _______________________________________________
>
> tigers@autox.team.net
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe:
> http://autox.team.net/mailman/options/tigers/twotigers@verizon.net
> _______________________________________________
>
> tigers@autox.team.net
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe: http://autox.team.net/mailman/options/tigers/drmayf@mayfco.com
_______________________________________________
tigers@autox.team.net
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
|