Ron,Never had access to LAT. My Tiger was sold new in Xenia, Ohio. The only
DPO installed a Ford 4 barrel carb 600 cfm and manifold. I got the car in 1985
and refreshed drive drain and installed a 360 Holley. I have an original 2
barrel carb and manifold from John Logan which is In reserve for later
installation. Runs so good with that 360. Gary Moore B9472283 tac311
--- On Thu, 2/3/11, Ron Fraser <rfraser@bluefrog.com> wrote:
From: Ron Fraser <rfraser@bluefrog.com>
Subject: Re: [Tigers] LAT manifolds
To: "'michael king'" <michael.s.king@gmail.com>, "'Tiger Talk List Tiger'"
<tigers@autox.team.net>
Date: Thursday, February 3, 2011, 4:57 AM
Michael
Shelby American was involved with the 2nd prototype. Ian Garrad was
well aware of the Cobra parts that they made available for the small block
Ford engine. Many of the LAT parts have corresponding Shelby part numbers
and were made by the same vendor.
I believe there were several official LAT Tiger lettered intake
manifolds; TBON shows at least 2 of them. I'm not up on LAT options so my
knowledge here is very limited.
Ron Fraser
-----Original Message-----
From: tigers-bounces@autox.team.net [mailto:tigers-bounces@autox.team.net]
On Behalf Of michael king
Sent: Wednesday, February 02, 2011 8:47 PM
To: Tiger Talk List Tiger
Subject: [Tigers] LAT manifolds
I know this has been covered a few times, that there were 2 edelbrock
manifolds that were used for the LAT options, but something that caught my
eye last week when i was looking through the graham rood book "works tigers"
was the manifold listed and photographed for the SCCA eligible options for
the tiger.
If memory serves me the LAT options early on were developed by HSC and doane
spencer to get the race tiger up and going. It shows a photo of what looks
like the HSC vented and hooded bonnet, the halibrand wheels and 4 wheel disc
setup along with the custom large fuel tank in the boot. The manifold was
what caught my eye... it is the early style 4BBL with 4 raised ports for the
carb, but it was lettered "TIGER" like the early cobra intakes.
Now i know there are 3 aftermarket "TIGER" lettered manifolds, and
apparently none were LAT options, but its interesting that one of them is
the one in the photo for the SCCA documents. Also the halibrands look like
the ones shelby ran on his tiger and different to the HSC kidney bean ones,
is it possible that the mfg of the "COBRA" lettered manifolds was asked to
do the TIGER one for the shelby tiger?
--
Regards
Michael King
_______________________________________________
Tigers@autox.team.net
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage:
http://autox.team.net/mailman/options/tigers/rfraser@bluefrog.com
No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.449 / Virus Database: 271.1.1/3416 - Release Date: 02/02/11
07:34:00
_______________________________________________
Tigers@autox.team.net
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage:
http://autox.team.net/mailman/options/tigers/arado7@sbcglobal.net
_______________________________________________
Tigers@autox.team.net
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
|