Ok, I was looking at the wiring diagram when I sent the previous post and
remembered I had some switches in the entertainment center and also found a
meter. I discovered that the switches do have numbers on the lugs BUT dont
have lugs for all the numbers. With the switch in the up position (lug 1- isnt
a #2, being the top)then lugs 1,6, and 7 are connected. In the middle
position, lugs 1,4,6 and 7 have continuity and in the bottom position, lugs
1,4,7 and 8 have continuity. SORRY for any confusin my earlier post created as
I was only looking at the diagram and obviously you need to use the two
togeter in order to wire things correctly or use the LUCAS definition of
"anyway that makes everything work with no smoke"
TtT
--- On Thu, 8/27/09, Tony Somebody <achd73@yahoo.com> wrote:
> From: Tony Somebody <achd73@yahoo.com>
> Subject: Re: [Tigers] Fw: Panel lights switch questions
> To: "'James Pickard'" <geowiz.sgy@cox.net>, tigers@autox.team.net,
rfraser@bluefrog.com
> Date: Thursday, August 27, 2009, 11:31 PM
> Jim- Im not sure what wiring diagram
> you are using but I highly recommend
> buying the laminated one from CAT. It has Mk1 on one side
> and Mk1A on the
> other. Im thinking about a spare to store under the
> passenger seat, since its
> water proof. It shows the red w/ a white stripe
> illuminating the gauge lights
> thru out the system. It connects to lug 8 not 1. If memory
> serves that switch
> is the only one installed upside down and if your switch is
> up side down, then
> lug 8 would appear to be lug #1. The way to tell what lugs
> are 1 and 2 and 7
> and 8 is use your meter- the two lugs w/ continuity are 1
> and 2. 7&8 have no
> continuity and that also decides top(1&2) vs bottom
> (7&8). If memory serves
> the gauge light switch was installed from the factory up
> side down BUT an
> original owner with switches in original position would
> have to confirm that.
> My second Mk1A was that way and Im pretty sure no wires or
> switches had been
> changed. Someone who knows for sure want to
> "speak up"concerning the gauge lights switch being
> opposite of all other
> switches????
> TtT
>
> --- On Thu, 8/27/09, Ron Fraser <rfraser@bluefrog.com>
> wrote:
>
> > From: Ron Fraser <rfraser@bluefrog.com>
> > Subject: Re: [Tigers] Fw: Panel lights switch
> questions
> > To: "'James Pickard'" <geowiz.sgy@cox.net>,
> tigers@autox.team.net
> > Date: Thursday, August 27, 2009, 10:43 PM
> > Jim
> > You can gently pry these
> switches apart,
> > clean the contacts and put
> > back together.
> >
> > The wire diagram shows the red wire, power, to
> terminal #4
> > and a red/ white
> > wire, gage illumination, at #8.
> >
> > Do you have a second R/W wire at #1?
> >
> > Ron Fraser
> >
> > -----Original Message-----
> > From: tigers-bounces@autox.team.net
> > [mailto:tigers-bounces@autox.team.net]
> > On Behalf Of James Pickard
> > Sent: Thursday, August 27, 2009 10:37 PM
> > To: tigers@autox.team.net
> > Subject: [Tigers] Fw: Panel lights switch questions
> >
> >
> > My panel lights switch is bad. It only works
> when it
> > is half way between
> > the middle and bottom position. But I have two
> > questions. I know up is
> > off, but I've forgotten what the difference is between
> the
> > middle and down
> > position. Second question concerns the wiring.
> My
> > switch has a red/white
> > wire attached to terminal 1 that disappears into the
> wiring
> > harness. The
> > wiring diagram shows no such wire. Anybody else
> have
> > this? If so, what is
> > it for? Thanks.
> >
> > Jim Pickard
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
>
> You are subscribed as achd73@yahoo.com
>
> Tigers@autox.team.net
> http://autox.team.net/mailman/listinfo/tigers
>
> http://www.team.net/archive
_______________________________________________
Support Team.Net http://www.team.net/donate.html
Tigers@autox.team.net
http://autox.team.net/mailman/listinfo/tigers
http://www.team.net/archive
|