tigers
[Top] [All Lists]

Re: [Tigers] Headers vs stock manifold

To: wsamouce@kc.rr.com, CoolVT@aol.com, tigers@autox.team.net
Subject: Re: [Tigers] Headers vs stock manifold
From: MWood24020@aol.com
Date: Sat, 28 Feb 2009 12:53:03 EST
I'd like to see real dyno data, as well. Some of the headers I've seen on  
Tigers I'd have to question whether there is any real help on the top end,  
looking at the bends, kinks etc. in the tubing. But, the Belanger type headers  
look pretty good. The Tri-Y design is meant to enhance lower end power, but I  
seem to remember they were tested and were poor performers...
 
Of course, it is all guess work without real numbers, on the same dyno, on  
the same day...
 
 
In a message dated 2/28/2009 8:18:42 A.M. Pacific Standard Time,  
wsamouce@kc.rr.com writes:

Mark,

Something else to consider - I have run my fuel line up  the back of the
engine to the back of the carb and put a heat insulating  sleeve over it.  I
did this because of fuel vaporization problems due  to so much of the fuel
line being exposed to the engine compartment heat  and the proximity to the
stock exhaust manifold and down tube.  Also,  did you have the headers
ceramic coated?  I just had the stock  manifolds coated and there is a big
difference in the engine compartment  heat.

I would also like to see what the LAT try Y manifolds would do in  a
comparison.

Duke
B382002037

-----Original  Message-----
From: tigers-bounces@autox.team.net  [mailto:tigers-bounces@autox.team.net]
On Behalf Of CoolVT@aol.com
Sent:  Saturday, February 28, 2009 10:06
To: tigers@autox.team.net
Subject:  [Tigers] Headers vs stock manifold

A while back someone referred to a  performance study comparing  the stock 
exhaust manifold with  headers.  When I put my engine back in this  Spring I
have 
to  decide if I want to bother with the headers.   The  CAT version  headers
run 
so close to things that I ended up putting a heat  shield  over the fuel
line, 
the starter and the shorty oil  filter.  I had to put  "heat protecting
socks" 
over 2 of the  spark plug wires. They make getting to the  mounting  for 
clutch  slave pretty difficult  too.  
As I remember someone had posted  that from dyno results the HP  would only 
begin to suffer above 5,000  RPM's.    So, anyone have  anything concrete to
help 
in  my decision?

Thanks, 
Mark
**************A Good Credit Score is  700 or Above. See yours in just 2 easy 
steps!  
(http://pr.atwola.com/promoclk/100126575x1218822736x1201267884/aol?redir=htt
p:%2F%2Fwww.freecreditreport.com%2Fpm%2Fdefault.aspx%3Fsc%3D668072%26hmpgID
%3D62%26bcd%3DfebemailfooterNO62)
Tigers@autox.team.net
http://autox.team.net/mailman/listinfo/tigers

http://www.team.net/archive
Tigers@autox.team.net
http://autox.team.net/mailman/listinfo/tigers

http://www.team.net/archive


**************A Good Credit Score is 700 or Above. See yours in just 2 easy 
steps! 
(http://pr.atwola.com/promoclk/100126575x1218822736x1201267884/aol?redir=http:%2F%2Fwww.freecreditreport.com%2Fpm%2Fdefault.aspx%3Fsc%3D668072%26hmpgID
%3D62%26bcd%3DfebemailfooterNO62)
_______________________________________________
Support Team.Net  http://www.team.net/donate.html

Tigers@autox.team.net
http://autox.team.net/mailman/listinfo/tigers

http://www.team.net/archive

<Prev in Thread] Current Thread [Next in Thread>