--===============6904502816392634127==
--000000000000911a7e05ea62318f
Ok, maybe it was that badly made? I do think the camera distorted one side
from the other. It is blanking plate to fit on the end of the Inlet
manifold on my Sprite when I have removed the Weber 45 DCOE. I have a
thick gasket stuck on the other side. I think it's a neater solution than
rag stuffed down it or a taping up job.
Regards
Daniel
On Thu, 6 Oct 2022 at 08:41, GUY DAY <grday@btinternet.com> wrote:
> A hole carrier.
>
> A Lucas parts template
> A very difficult to judge sized hole carrier or template for Lucas parts
> shown without a scale bar.
>
>
>
> ------ Original Message ------
> From: "Weslake1330 via Spridgets" <spridgets@autox.team.net>
> To: "Spridgets" <spridgets@autox.team.net>
> Sent: Wednesday, 5 Oct, 22 At 20:26
> Subject: [Spridgets] Name that part (real LBC content).
>
> Hi List,
>
> Well the part doesn't have a real name because I made it from 6 mm (its
> probably old enough to be 1/4") aluminium plate the previous owner of my
> house left behind in the garage about 20 years ago. If I could have bought
> one I would have.
>
> Lacking both a pillar drill and a Rolls-Royce (aviation?) apprenticeship
> where you get to file metal blocks for several years, it's almost the best
> I could manage. The Bosch jigsaw wasn't keen (it never is) on cutting
> aluminium plate this thick but managed some of it.
>
> I'm not particularly tempted to make another one because it's not
> something I'm likely to use very often and it will get the job done despite
> being slightly lower than the standard I'd hoped for. So, what is it?
>
> Regards
>
>
> Daniel
> ------------------------------
> ------------------------
>
> spridgets@autox.team.net
>
> Donate: http://www.team.net/donate.html
> Suggested annual donation: $12.75
>
> Archive: http://www.team.net/pipermail/spridgets
> http://autox.team.net/archive
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/spridgets/grday@btinternet.com
>
>
--000000000000911a7e05ea62318f
Content-Transfer-Encoding: quoted-printable
<div dir=3D"ltr">Ok, maybe it was that badly made?=C2=A0 I do think the cam=
era distorted one side from the other.=C2=A0 It is blanking plate to fit on=
the end of the Inlet manifold on my Sprite when I have removed the Weber 4=
5 DCOE.=C2=A0 I have a thick gasket stuck on the other side.=C2=A0 I think =
it's a neater solution than rag stuffed down it or a taping up job.<div=
><br></div><div>Regards</div><div><br></div><div><br></div><div>Daniel</div=
></div><br><div class=3D"gmail_quote"><div dir=3D"ltr" class=3D"gmail_attr"=
>On Thu, 6 Oct 2022 at 08:41, GUY DAY <<a href=3D"mailto:grday@btinterne=
t.com">grday@btinternet.com</a>> wrote:<br></div><blockquote class=3D"gm=
ail_quote" style=3D"margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,=
204,204);padding-left:1ex"><u></u> <div><div dir=3D"auto" style=3D"unic=
ode-bidi:embed">A hole carrier. <div><p>A Lucas parts template</p>A very d=
ifficult to judge sized hole carrier or template for Lucas parts shown with=
out a scale bar.<br><blockquote style=3D"margin:0px auto;padding:0px 2em;bo=
rder-left:2px solid rgb(0,173,229);white-space:pre-wrap"><br><br>------ Ori=
ginal Message ------<br>From: "Weslake1330 via Spridgets" <<a =
href=3D"mailto:spridgets@autox.team.net"; target=3D"_blank">spridgets@autox.=
team.net</a>><br>To: "Spridgets" <<a href=3D"mailto:spridge=
ts@autox.team.net" target=3D"_blank">spridgets@autox.team.net</a>><br>Se=
nt: Wednesday, 5 Oct, 22 At 20:26<br>Subject: [Spridgets] Name that part (r=
eal LBC content).<br><br><div dir=3D"ltr">Hi List,<div><br></div><div>Well =
the part doesn't have a real name because I made it from 6 mm (its prob=
ably old enough to be 1/4") aluminium plate the previous owner of my h=
ouse left behind in the garage about 20 years ago. If I could have bought =
one I would have.</div><div><br></div><div>Lacking both a pillar drill and =
a Rolls-Royce (aviation?) apprenticeship where you get to file metal blocks=
for several years, it's almost the best I could manage. The Bosch jig=
saw wasn't keen (it never is) on cutting aluminium plate this thick but=
managed some of it.</div><div><br></div><div>I'm not particularly temp=
ted to make another one because it's not something I'm likely to us=
e very often and it will get the job done despite being slightly lower than=
the standard I'd hoped for. So, what is it?</div><div><br></div><div>=
Regards</div><div><br></div><div><br></div><div>Daniel</div></div> <hr>----=
--------------------<br>
<br>
<a href=3D"mailto:spridgets@autox.team.net"; target=3D"_blank">spridgets@aut=
ox.team.net</a><br>
<br>
//www.team.net/donate.html</a><br>
<br>
Archive: <a href=3D"http://www.team.net/pipermail/spridgets"; target=3D"_bla=
nk">http://www.team.net/pipermail/spridgets</a> <a href=3D"http://autox.te=
am.net/archive" target=3D"_blank">http://autox.team.net/archive</a><br>
<br>
ets/grday@btinternet.com" target=3D"_blank">http://autox.team.net/mailman/o=
ptions/spridgets/grday@btinternet.com</a><br>
</blockquote></div></div></div></blockquote></div>
--000000000000911a7e05ea62318f--
--===============6904502816392634127==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
------------------------
spridgets@autox.team.net
Archive: http://www.team.net/pipermail/spridgets http://autox.team.net/archive
--===============6904502816392634127==--
|