Sorry, Dean. I'm wrong. There are three studs holding the light assembly. I just
ran into the garage to check mine.
To access the studs on the inside, lift the hood. You will see a cutout just in
front of the wheel arch. You can put your hand in there to put the screws on and
then tighten them up with a nut driver.
Vic W.
Dean.Dashwood@enron.com wrote:
>
> Vic,
>
> No studs - at least, not on my existing unit, but I'll see what the new one
> has when it's delivered.
>
> So, that doesn't answer the question - how do you get the nuts and washers
> on the back? It's a hollow unit, and I can't find an access hole big
> enough to get my hand through to reach the back.....
>
> I'm sure I'm missing something obvious here!
>
> Dean
> ------------------------
>
> To: Dean.Dashwood@enron.com
> cc: spitfires@autox.team.net
>
> Subject: Re: Light assembly question
>
> No screws, just two bolts with washers and nuts. In fact, AFAIK, there are
> two
> studs on the back of the base that go through the body panel and then the
> washers and nuts go on the studs.
>
> Vic Whitmore
> 76 Spitfire
> Thornhill, Ontario
>
> Dean.Dashwood@enron.com wrote:
> >
> > Guys,
> >
> > Ok, it's my turn to ask a really stupid question.
> >
> > First of all, a bit of background. Last week I discovered some
> > "interesting" things happening with my front side-light and indicator on
> my
> > 1500. Turn the lights on, the indicator tell-tale comes on but the side
> > light doesn't. Turn the indicator on, and if you're lucky the side-light
> > flashes but the indicator doesn't. That's what I mean by "interesting".
> >
> > On the advice of some club members, I checked out all the earths, and
> > couldn't find anything wrong. But a bit more investigation revealed that
> > they had pointed me at least roughly in the right direction. I removed
> the
> > front light assembly, and with the help of an ohm-meter, discovered a
> > couple of thousand ohms resisatance between both the bulb holders and the
> > earth connection on the assembly. Cross-checking with the wiring diagram
> > confirmed that this would indeed cause the symptoms I was seeing, with
> > current from the side-light flowing "backwards" through the indicator
> > circuit, lighting the tell-tale, and probably earthing through another
> > indicator. I decided the best solution was to replace the assembly, so
> > I've ordered a new one.
> >
> > Now, electrically, I have no problem with this. My stupid question
> relates
> > to the physical fitting of this lighting assembly to the car. The
> assembly
> > contains six screw-holes. As far as I can tell, four of these are for
> > attaching the assembly to the car, and the other two are for attaching
> the
> > coloured panels onto the assembly. The problem is that, of the four
> screws
> > which attach the assembly to the car, I only have holes on the car for
> two
> > of them - and I only have two screws. One of the two screws is a
> > self-tapping type, and secures the assembly to the car without any nuts
> or
> > anything on the other side. The other screw is also a self-tapping type,
> > but the hole is too big for it, so it serves no useful purpose. My whole
> > lighting assembly is held in by one screw, and no nuts!
> >
> > Now, I'm sure this isn't right, but I'm not sure how it's supposed to be
> > held on. Are there supposed to be nuts/washers? Seems to me that there
> > probably should be, but I can't figure out how to get my hand round the
> > back to position the nuts onto the screws! Or are these supposed to be
> > self-tapping screws - in which case I'll buy another one, drill a couple
> > more holes, and use three screws instead of one (ignoring the too-big
> > hole)?
> >
> > Ok, I said it was a stupid question, but I'd rather not have bits of my
> car
> > fall off just because I couldn't figure out how to put a nut on the back
> of
> > screw.....
> >
> > Thanks,
> >
> > Dean
> > ---------------------
>
> --
> Vic Whitmore
> 76 Spitfire
> Thornhill, Ontario
>
> http://www.vicwhit.com
--
Vic Whitmore
76 Spitfire
Thornhill, Ontario
http://www.vicwhit.com
|