Scott - I second the asbestos content. A homeowner can remove small
amounts, but if a big area, it may be best for a professional. If you
touch it, wear a good respirator - more than a dust mask. I think it is
N99 vs N95 as in the percent filtered.
Look and see if you have two layers of wood for your flooring. If so, I
would definitely at least take off the top layer. Careful cutting with
a circular saw should make it easy.
It will probably be easiest to just take a circular saw and cut around
the edge of the room to take out the subfloor. I did this in one
bathroom earlier this year. I had water damage near the shower and
toilet and decided it was easiest to just take up the plywood and 1x6
floor boards and put down new plywood. I used the oscillating cutter in
the corners where the circular saw couldn't get. 3/4" plywood was close
enough to the 1x6 then I topped it with a layer of 1/2" plywood in the
opposite direction. The floor is very solid. I went a step further
with a layer of Ditra membrane then tile.
My second bathroom had sheet vinyl that had to come up. I tried a heat
gun and a scraper blade in my oscillating tool, but both took forever.
I ended up using my rotary hammer with a chisel bit - an older version
of this:
http://www.harborfreight.com/1-18-in-10-amp-heavy-duty-sds-variable-speed-rotary-hammer-69274.html
and
http://www.harborfreight.com/12-in-sds-max-type-masonry-chisel-bit-set-3-pc-60377.html
This quickly took up the floor in strips. This was over a concrete
slab. I had a couple bits remain, so just hit them with the angle
grinder with a concrete grinding disk. I first tried the angle grinder
with a wire cup, but the adhesive was too soft, so just smeared. A
sanding disk would be better for the wood if you keep the existing floor.
They make a compound for leveling the floor, so if you have some scrapes
and divots, you can just skim the floor and have a near perfect
surface. This means you don't have to be as careful removing the old
stuff if you try and keep the existing wood.
While working, I hung a box fan in the window on high to exhaust all the
mess outside and wore a respirator. My safety glasses kept fogging, so
I switched to swim goggles. I also wore my hearing protection as it was
noisy. Best to take care of yourself so you can keep doing the projects.
Brian
On 11/3/2015 11:02 AM, Scott Hall wrote:
> So, the garage had part of the floor covered with vinyl tile.
>
> No sweat. Bought a floor scraper from Harbor Freight. Nice tool. Very
> sharp, thick blade on the end of a pole. Good for smooth concrete subfloors.
>
> Now I'm moving to the bathroom, which isn't over a slab--it's hung off the
> side of the building over a crawlspace. Which means a wood subfloor.
>
> The scraper is too sharp. The vinyl tile is at least two layers deep (they
> just tiled over the old tile) and it flexes. So running the scraper over
> it, it either bites into the tile and binds up (it can't bear against the
> rigid concrete subfloor), or it bites into the wood floor itself.
>
> I need...a dull(er) scraper. Maybe. Something I can lever under the tile
> that won't bite into the wood or tile. Or do I just need something else?
> Or...how can I remove vinyl tile from a wood subfloor? The tile is so old
> that it's disintegrating and I can't pull it up a tile at a time. But it's
> also too crumble-y to try to get a piece at a time--it's take months just
> to do the 10-by-6 area.
>
> Looking for advice--the garage mahal has a bathroom, and it's going to be
> awesome. As soon as I get this vinyl tile up.
>
> Scott
_______________________________________________
Shop-talk@autox.team.net
Archive: http://www.team.net/archive
|