Jim - Depending on the length, it may be worth a little more labor to
install rigid PVC. 1 in. x 10 ft. Sch. 40 PVC Conduit is $2.58 at my
local Home Depot. Assuming you have a 50' run, that is $12.90 for the
pipe vs $57.50 for the flex at the price below. I know HD vs. McMaster
may not be an apples to apples, but it is worth a comparison.
As a side note, the PVC conduit can also be made flexible with a heat
gun. Warm it on low for a minute or two then hold it in place for a
little bit and you have a custom piece with no fittings. Heat all the
way around the pipe so you get a clean bend. I don't recommend this for
a standard 90 or 45 fitting, but it is handy to use for small offsets.
Many areas will require schedule 80 for 110V exposed areas as it is more
durable. That shouldn't matter for low voltage.
I agree with Mark to go with bigger conduit, especially over a long run
as it is much easier to pull wires with room.
Don't have a fish tape to get a pull string? Tie a light string to
paper towel and wrap it with a bit of tape. Feed it in one end and put
your vac on the other. You can then pull small stuff with the string or
pull a heavier cord for tougher pulls.
Brian
On 7/8/2011 8:59 PM, Mark Miller wrote:
> I think you should be able to get the electrician to run an empty flex
> conduit in the same trench while it is open for the goodwill, as it really
> isn't any extra work for them. Asking them to place and glue in fittings
> and such is too much to hope to get for free/ little.
> And two empty conduits means you can run a pex line through one if water
> becomes a desire later (really you can use one for both but it makes more
> sense to keep them separate if you can). If you can buy the conduit ahead
> of time and have it there, perhaps with a case of sodas for while working
> and a case of beer for afterwards. . .
>
> 1" flex at McMaster is $1.19 a foot, probably much less at a local
> electrical supply house. It is way bigger than you'd need, but it is easier
> to snake through bigger tubing.
> http://www.mcmaster.com/#nonmetallic-conduit/=d3ftbz
>
> Good luck!
>
> Mark Miller
> <<<
> Message: 6
> Date: Wed, 6 Jul 2011 16:30:43 -0500
> From: Jim Stone<jandkstone99@msn.com>
> To:<jamesf@groupwbench.org>,<shop-talk@autox.team.net>
> Subject: Re: [Shop-talk] CAT Cable to Garage
> Message-ID:<COL115-W552BD09F2213304D903092CC5E0@phx.gbl>
> Content-Type: text/plain; charset="us-ascii"
>
> Thanks guys. I don't want to pay the electrician to do the work, so I will
> just have to time it right and be there to drop a seperate run in at the
> same
> time. I will make certain I am ready to go when they do their work.
> _______________________________________________
>
> Shop-talk@autox.team.net
> Donate: http://www.team.net/donate.html
> Suggested annual donation $12.96
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage:
>http://autox.team.net/mailman/options/shop-talk/bk13@earthlink.net
_______________________________________________
Shop-talk@autox.team.net
Donate: http://www.team.net/donate.html
Suggested annual donation $12.96
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
|