Framing nailers (all nailers in general) are great! I have a full set
from brad nailers up to framing nailers and wouldn't think about working
without them.
In the 15 years I have been using them I have had one injury and one
safety breach because of me using the framing nailers. I was nailing
blocking into a wall, holding the 2x4 block between two studs with my
hand about 16" away from the gun. I pulled the trigger and my thumb
light up! It was bleeding and I figured that the nail had ricocheted off
the stud and grazed my thumb. Cleaning it up showed a small nick. Not
bad, I mused, but what is this blood on the other side of my thumb??!??
It turns out that the nail went into the stud and followed the grain
back out, launching the nail towards my thumb. The nail (#16) went
though my thumb head and all! I never found the nail, but an X-ray found
that it had totally missed the bone.
The other time I was nailing siding to the studs and was walking down
the stud with the gun, shooting #8 nails every foot. One nail head blew
through the siding. I figured I had wandered off the stud and tried
again, only to have the same thing happen. Turns out that I was nailing
a stud over a door and was now shooting through the door opening. Glad
there was nobody on the other side!
All my guns are set for sequential use. Folks who use their guns daily
generally bounce nail, but I am too safety conscious for that. Even
though I have been using guns for a long time, I would rather take the
extra time to be safer than make another trip to the ER.
Peace,
Pat
Thusly spake David C.:
> I just picked up what could possibly be my most dangerous tool- a
> Hitachi NR83A2 framing nailer. It's awesome.
>
> I have a small framing job coming up (framing in a 12 x 12 foot rolling
> door opening on my pole building shop and installing a pair of 2'6"
> doors in the new wall to replace the rolling door) and wasn't looking
> forward to swinging a framing hammer any more.
>
> I did a little research on the web and went through a couple of pawn
> shops and found that apparently the Hitachi NR83A is kind of the default
> framing nailer for most of the framing carpenters around here.
> Everything I read and heard gave me the impression that they are pretty
> bulletproof. One pawn shop had about seven of them in varying
> conditions, so I picked out the one that seemed to be in the best shape
> and paid $137 (plus tax) for it. I stopped at the orange Borg and
> bought a box each of Senco 16d and 8d nails for it, took it out to the
> shop and tried it out. It works great. I have a few brad nailers from
> 23 to 16 gauge, but I've never used a framing nailer. This thing is an
> animal. Fortunately it's the newer A2 model so I can switch the trigger
> from bump firing to sequential firing. I tried it both ways, and bump
> firing gave me a lot of double nails. I can see where bump firing would
> be great for installing subflooring or sheathing, but for framing
> (especially toe nailing) I'm going to stick to sequential firing.
>
> So, anyone got any good framing nailer stories or tips?
>
> I'm almost looking forward to the framing job. I wish I had it a few
> years ago when I built the 24' x 48' tractor shed on the back of the shop.
>
> Dave C
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
>
> You are subscribed as pat@hornesystemstx.com
>
> Shop-talk mailing list
>
> http://autox.team.net/mailman/listinfo/shop-talk
>
> http://www.team.net/archive
>
> ------------------------------------------------------------------------
>
>
> No virus found in this incoming message.
> Checked by AVG - http://www.avg.com
> Version: 8.0.173 / Virus Database: 270.7.5/1701 - Release Date: 9/30/2008
>7:08 PM
>
>
--
Pat Horne, Owner, Horne Systems
(512) 797-7501 Voice 5026 FM 2001
Pat@HorneSystemsTx.com Lockhart, TX 78644-4443
www.hornesystemstx.com
-- We support Habitat for Humanity - a hand UP, not a hand OUT --
_______________________________________________
Support Team.Net http://www.team.net/donate.html
Shop-talk mailing list
http://autox.team.net/mailman/listinfo/shop-talk
http://www.team.net/archive
|