oletrucks
[Top] [All Lists]

Re: [oletrucks] Passenger-side vent

To: "Lee Glenn" <lglenn@webslnger.com>
Subject: Re: [oletrucks] Passenger-side vent
From: "joe" <chevy1@jps.net>
Date: Thu, 4 May 2000 20:49:55 -0700
No fresh air intake on my Vintage Air system.  All I have are four lines
heading into a Polished Aluminum bulk fitting that direct the A/C and water
into the cab.  I just could bring myself to weld up the center cowl vent
after all the memories of cranking the vent open on a hot summer night and
having the fresh cool breeze rush through the cab.  My 50 as you know didn't
come with vent windows so the center cowl vent "Not an original 1950 Cab so
I didn't have a  drives side cowl vent" was my only source of direct outside
air.  Funny after welding everything else up in the truck that I just kept
putting off welding up that vent every single day until I finally said "I'm
leaving it"!

Just had to have A/C and have only used it twice?  But I've cranked the vent
open more times then I can count!

Joe Garcia
1950 Chevrolet 3100
Yuba City, Ca
http://chevy1.freeservers.com/
http://jeepster.freeservers.com/
http://50chevy.freeservers.com/
----- Original Message -----
From: Lee Glenn <lglenn@webslnger.com>
To: joe <chevy1@jps.net>
Sent: Thursday, May 04, 2000 8:00 PM
Subject: Re: [oletrucks] Passenger-side vent


> Hi, Joe.
>
> I think I have a deluxe heater.  I went down to the body shop with the
digital
> camera, but they lock the shop up over the noon hour.  I'll try again next
> week.  About the Vintage Air heat and air unit....  does it have a fresh
air
> intake somewhere?  I'm  having durn-near everything welded up (cowl vent
and
> both side vents) and I'm thinking about going with the Vintage Air Sure
Fit
> design.
>
> Later,
> -Lee
>
> joe wrote:
>
> > I cut the vent out and filled it in on my 1950 3100 to clean up the body
> > lines.  If you have the deluxe heater that bolts to the kick panel then
you
> > will be making it practically useless because you restricting the air
flow.
> > I went with Vintage Air heat and air unit so I no longer needed the side
> > vent.
> >
> > Joe
> > http://chevy1.freeservers.com/
> > http://jeepster.freeservers.com/
> > http://50chevy.freeservers.com/
> > ----- Original Message -----
> > From: Lee Glenn <lglenn@webslnger.com>
> > To: oletrucks oletrucks <oletrucks@autox.team.net>
> > Sent: Tuesday, May 02, 2000 8:11 PM
> > Subject: [oletrucks] Passenger-side vent
> >
> > > Hello, all.
> > >
> > > Got a question for ya'll...  Suppose my body guy welded up the
> > > passenger-side cowl vent on my '49, even though I didn't tell him too.
On
> > > the one hand, it eliminates a potential area for rust.  On the other,
> > > doesn't the heater get fresh air from there?  What's the down side to
> > > welding this up?
> > >
> > > Curious,
> > > -Lee
> > >
> > > Ben Bennett wrote:
> > >
> > > > Here goes nothing!
> > > > --
> > > > Ben Bennett
> > > > Westminster,CA (just south of Long Beach)
> > > > 55 2ND
> > > > Http://home.earthlink.net/~greyhawk2/
> > > > oletrucks is devoted to Chevy and GM trucks built between 1941 and
1959
> > >
> > > oletrucks is devoted to Chevy and GM trucks built between 1941 and
1959
> > >
>
>

oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959

<Prev in Thread] Current Thread [Next in Thread>