Can you send me your gear to see if we Can machine it in what quanty
at equitable cost in our shop. Will Return Afterwards.
Thank you.
Sent from my iPhone
Roland 650 208-3684
On Aug 25, 2009, at 4:36 PM, Ron Engelhardt <nobbc@sonic.net> wrote:
> Plastic? The gears I have look like they're made out of some kind of
> fiber composite. I thought of cutting two in half and glueing them
> together or using them as a mold but so far, I haven't gotten
> inspired. Somebody must sell them as I imagine many people are in
> the same boat I'm in. I've noticed that the gears strip when the
> speedo changes to an even thousand and have a few that are stopped
> at 49999 or thereabouts, maximum thrust needed on the gear at that
> point I imagine.
>
> Ron
> 58 MGA
>
> andy preston wrote:
>
>> Ron, I tried to repair the odometer on my A before sending it to
>> Nisonger.
>> The little plastic gears were broken and I had no way of fixing
>> them. I
>> must say that it works great now but $170 is not chump change.
>> Andy
>> -----Original Message-----
>> From: nobbc-bounces@autox.team.net [mailto:nobbc-
>> bounces@autox.team.net] On
>> Behalf Of Ron Engelhardt
>> Sent: Tuesday, August 25, 2009 2:15 PM
>> To: North Bay British Car Club
>> Subject: Re: [Nobbc] Suggestions, please
>> Regarding the Jaeger speedos, has anyone found a source for the
>> little fiber gears that drive the odometer and trip odometer
>> wheels. I've been searching for a source for 20 years and have
>> never been able to find one. The speedo places wont sell them, just
>> want to refurbish your unit. My speedo works great but the
>> odometers don't, not a major problem but it would be nice to get
>> them working again. I have lots of speedos I've scavanged parts
>> from over the years but the fiber washers never seem to last. I
>> guess they hit roughly 30-40 years and die ;-)
>> Ron
>> 58 MGA
>> wendell bain wrote:
>>> Hi Mike, Greg, Andy, et all,
>>>
>>> My experience with these repair services is as follows:
>>>
>>> I had the Morgan's speedo repaired at Palo Alto Speedometer. After
>>> three
>>> tries and $180. they couldn't get it right. I give them credit
>>> for trying everything
>>> including a new cable. I don't know about divine intervention,
>>> but after about
>>> six months the thing started working fine except it reads about
>>> five mph
>>> fast and at a stop it still reads 5 mph. I guess it's really not
>>> fixed but at
>>> least it doesn't have a 35 mph wave in the needle anymore.
>>>
>>> My Morgan has a TR-3 engine. Factory manual states this engine's oil
>>> pressure should read 70 psi @ 3000 rpm warm, so it would seem once
>>> Mike adjusted his oil pressure where it should be all is right with
>>> the world... Or at least the guage.
>>>
>>> All of your suggestions are very helpful. Thanks very much.
>>>
>>> Wendell
>>> 59 Morgan +4
>>>
>>> On Aug 25, 2009, at 11:09 AM, Mike Gianandrea wrote:
>>>
>>>
>>>> Hi Greg,
>>>>
>>>> I had my oil pressure gauge for my TR4 repaired at West Valley
>>>> Instruments in Reseda, suggested to me by Moss Motors. He did it
>>>> overnight for me, charged me $93.75 plus tax and freight.. It
>>>> worked for two days, but my newly rebuilt motor was putting a
>>>> consistant 100 PSI, when it should have been putting out about
>>>> 60 PSI. Consequently, the gauge started leaking again. I
>>>> adjusted the oil pressure down to 60-70 PSI, and re-repaired the
>>>> gauge myself, and it has been working fine since. The
>>>> gentleman's name is Morris, Tel 818-758-9500. I can't blame the
>>>> failure of my gauge on him, with my oil pressure as high as it
>>>> was, and he is referred by Moss, so who knows. You could check
>>>> with Moss as to any complaints, and ask Morris about a warranty.
>>>>
>>>> Michael
>>>> 64 TR4
>>>> ----- Original Message ----- From: "Greg Tatarian" <gtwincams@gmail.com
>>>> >
>>>> To: "North Bay British Car Club" <nobbc@autox.team.net>
>>>> Sent: Monday, August 24, 2009 1:34 PM
>>>> Subject: [Nobbc] Suggestions, please
>>>>
>>>>
>>>>
>>>>> Hello Members,
>>>>>
>>>>> I think this subject has come up before, but I'm looking for a
>>>>> good shop to rebuild a Smiths dual temp/oil gauge. Nxxxxxxx'x
>>>>> in NY was a dead end - they gave me a bit of a brush off when I
>>>>> told them I just needed the capillary tube replaced and didn't
>>>>> want the entire gauge brought up to concours standards. The
>>>>> shop I won't name in the Peninsula took a very long to repair a
>>>>> gauge for me some years back and the repair didn't last. Has
>>>>> anyone used the few other shops that do this work, and can they
>>>>> please share their opinions? Andy - did you have all of your
>>>>> MGA gauges rebuilt, or are they new?
>>>>>
>>>>> Thanks in advance,
>>>>>
>>>>> Greg Tatarian
>>>>> _______________________________________________
>>>>> Nobbc mailing list
>>>>> Nobbc@autox.team.net
>>>>> http://autox.team.net/mailman/listinfo/nobbc
>>>>
>>>> _______________________________________________
>>>> Nobbc mailing list
>>>> Nobbc@autox.team.net
>>>> http://autox.team.net/mailman/listinfo/nobbc
>>>
>>> _______________________________________________
>>> Nobbc mailing list
>>> Nobbc@autox.team.net
>>> http://autox.team.net/mailman/listinfo/nobbc
>> _______________________________________________
>> Nobbc mailing list
>> Nobbc@autox.team.net
>> http://autox.team.net/mailman/listinfo/nobbc
>> _______________________________________________
>> Nobbc mailing list
>> Nobbc@autox.team.net
>> http://autox.team.net/mailman/listinfo/nobbc
> _______________________________________________
> Nobbc mailing list
> Nobbc@autox.team.net
> http://autox.team.net/mailman/listinfo/nobbc
_______________________________________________
Nobbc mailing list
Nobbc@autox.team.net
http://autox.team.net/mailman/listinfo/nobbc
|