paul.hunt1@virgin.net wrote:
>
> If you do have the Opus ('Opeless) system then you should already have a
> solid-state trigger (magnetic) in place of points, which is all the
> Pertronix is.
Ok, what you are saying here is, 1) why replace the same with the
same
and 2) the Opus is junk. So that's a little confusing. But, I
didn't want
to have the big Crane EI box addition. I'm also believing the
Pertronix
is going to be more dependable.
> The Opus system needs the 6v (1.5ohm) coil and two ballasted
> supplies. One was the loom ballast used on all rubber bumper MGBs and had a
> white (or white/brown) at the fuse-box end and a white/light-green at the
> coil end. The other was a resistor for the electronics that had a
> white/blue to the distributor. The distributor also had a full12v
> unballasted supply.
I pulled out my Bentley Manual to follow along. Yes, White from
fuse box
into the resistor and White/Light-green to + on the coil.
Also, on the white side of the resistor, 2 more whites come out,
one to
another resistor, which comes out White/Blue to the distributor
and another
white straight to the distributor. The other wire to the
distributor is
White/Black, and goes to the - on the coil and on to the Tach.
That all looks
good.
> If the Opus electronics have been disabled in some way, and you have points
> firing the coil directly, then you can replace the points with the
> Pertronix.
No, the Opus is running.
> With either points or Pertronix, to use a 12v (3 ohm) coil you must have a
> full 12v (white) to the coil +ve and not the ballasted 12v
> (white/light-green). Again with both systems to use a 6v coil you must have
> a ballasted 12v on the coil +ve.
Ok, this is what I wanted. When I put the coil in I use the
White, and by-pass
the White/light-green. As to the resistor going into the
distributor, that may
or may not be used depending on the install instructions of the
Pertronix. I'm
guessing.
> You really should determine exactly what you currently have, in the shape of
> 12v or 6v coil, ballast or no ballast, points or Opus trigger, and Opus
> electronics or not before you change anything.
Right. No points, stock coil (I'm sure it is). Of course, it's
put away, I can't
even look at it.
So I scanned in the wiring diagram, and I'm going to color it in.
I see that
Skye has that already, but just for the '75, I'm doing the '76
and '77 supplement.
Paul.
> ----- Original Message -----
> From: "Paul Root" <proot@iaces.com>
> To: <mgs@autox.team.net>
> Sent: Thursday, January 10, 2002 2:54 PM
> Subject: Pertronix ignition and coil
>
> > Hi all,
> > Thanks to a generous gift certificate to the Little
> > British Car Company from Jim Schulte, I bought a pertronix.
> >
> > I'm certain I have the correct EI, the LU-141 for my
> > '77B. It has a dizzy with the big block on the side, the
> > amplifier. The Moss catalog calls it the 'Opus'.
> >
> > Anyway, I think I bought the wrong coil, but I also
> > think, it probably doesn't matter. I got the 3 OHM 40,000v
> > Flame Thrower. A quick glance at the install instructions said
> > that this is for non-ballasted systems, and if you want
> > ballasted,
> > then get the 1.5 OHM or remove the ballast.
> >
> > So, should I return it or remove the ballast? And the
> > ballast is the resistor block on the side right?
--
Paul T. Root E/Mail: proot@iaces.com
600 Stinson Blvd, Fl 1S PAG: +1 (877) 693-7155
Minneapolis, MN 55413 WRK: +1 (612) 664-3385
NIC: PTR FAX: +1 (612) 664-4779
///
/// mgs@autox.team.net mailing list
/// or try http://www.team.net/cgi-bin/majorcool
///
|