-------------< COMMENTS BY Monadnoc >--------------
Thanks Mike. I may put off this conversion until this winter. Would
like to get the car to a "driveable" condition before the snow hits. I
have a garage and "New England Heat", i.e. above 32 degrees, so I will
not be rolling around on the icy driveway, swapping axles! Changing the
e-brake etc. is no problem, cuz it's seized up anyway and it sounds like
the full rear end swap will be the way to go. I will see if the
ambition actually keeps pace with the endless ideas.
Wally / Templeton, MA
71 MGB with driver's side floor pan installed, now to get out the
sawz-all and remove the other side.
----------< END OF COMMENTS BY Monadnoc >----------
Date sent: Mon, 7 Jul 1997 17:57:50 -0400 (EDT)
From: Arthur Pfenninger <ch155@FreeNet.Buffalo.EDU>
To: Wally Teto <monadnoc@wgserv.crystal-mtn.com>
Copies to: mgs@autox.team.net
Subject: Re: Wheel swap decision
Send reply to: Arthur Pfenninger <ch155@FreeNet.Buffalo.EDU>
Sorry to reply so late, but I was away from my computer over the
extended weekend. I am in the process of switching my '74 to wires,
and it has been a bit of a pain. The front wheel components were all
OK, but to remove my old ones took some time. I also found out that
you have to change the whole rear end unless you have a way of
pulling the axle half-shafts. When you switch rear ends, you have to
switch e-brake cables also. I think, personally, that it's a really
neat conversion, and if you got 'em, you might as well use 'em.
Besides, when will you ever get the chance to own something so
"British" as wire wheels?
Good Luck,
Mike
Even though the spoked wheels can be a problem they add value and
looks to the car. My suggestion would be to switch the rear axle,
not a real big job and switch the complete front suspension, again not a
big deal. It's only held on with a few bolts. While the suspension is off
you could take some time and rebuild it. The winter months are a good time
to do this assuming you have a basement to work in. It is a lot easier to
work on the suspension if you don't have to crawl around on the ground!
...Art
~On Mon, 7 Jul 1997, Wally Teto wrote:
> Many thanks to Todd, Rick and the others who responded with great
> ideas and personal experience on my decision of whether to swap my disk
> wheels for wires. I had thought that I could get away in the rear with
y> swapping half-shafts, but apparently this is not possible. And I had
> conveniently forgotten about the inherent problems with tubes, truing,
> etc. I think we will just blast and paint the disks for now and leave
> the wires for someday down the road when we have time on our hands (20,
> 30 years maybe?). This whole project started out as a 2 week job to get
> this car "roadworthy", and is slowly evolving into a complete
> tear-down. I know, you guys have all "been there, done that, got the
> T-shirt". If I didn't love these blasted infernal machines so much, I'd
> chuck the project for some American iron, but where is the redeeming
> social value in that? Besides, I got a 20 year old kid hooked on LBC's
> and that can't be all that bad. Even his 15 year old brother is
> starting to take interest...must be his impending license exam coming up
> next year!
>
> Sorry if this post is a duplicate...my ISP is somehow related to the
> Prince of Darkness and I think the 1st post is sitting in some black
> hole.
>
> Wally / Templeton, MA
> 71 MGB in restoration
>
> remember, if it's got tits or tires, you're gonna have problems...
>
>
|