mgb-v8
[Top] [All Lists]

Re: [Mgb-v8] Fwd: Shortened water pump

To: David Kernberger <dkern@napanet.net>, "Carl Floyd" <cmfloyd@chartertn.net>
Subject: Re: [Mgb-v8] Fwd: Shortened water pump
From: Barrie Robinson <barrie@look.ca>
Date: Fri, 29 Aug 2008 09:06:41 -0400
David et al,

I did not install my engine (no facilities for large lumps).  All I 
can say is that it was, and is, installed and works.  The chaps who 
did it listed all the problems they had with the installation (to 
justify their invoice!) and this was not a problem area !!!!!  If 
anyone wants I can take photos and send.



At 01:58 AM 8/29/2008, David Kernberger wrote:
>To all,
>
>         For what it is worth, I am with Darius.  It seems to me that
>either this short pump will require a pulley with a different amount
>of offset, or the other pulleys in the system will also need to be
>changed to match.  All pulley grooves for a single belt must lie in
>the same plane.  I even wonder if the short pump might locate the fan
>in the old belt plane??  Or maybe awfully close?  Am I missing
>something here also???
>
>Cheers,
>Dave K.
>
>---------------------------------------------------------------------
>
> >Maybe this article will help:
> >
> >http://www.britishv8.org/Articles/Shortie-Water-Pump.htm
>
>
>Carl
>
> >
> >
> >-------------------------------------------------------------------------
> >
> >
> >>  Barrie,
> >>
> >>      First, thanks for the quick response. However, I'm still not sure my
> >>  question was understood.
> >>
> >  > I've looked at the picture of the modified water pump and a 3 inch thick
> >  > unit would indeed benefit my application.
> >  >
> >>  As you stated it appears that the body of the water pump has 
> been machined
> >>  on its "engine side" and that the protruding nose of the shaft have been
> >>  machined off. The water pump pulley mounting flange has been pressed
> >>  toward the body of the pump and the overall change offers a considerable
> >  > savings in length.
> >  >
> >  > Now for the difficulty.  Since the pulley mounting flange has been moved
> >  > toward the engine and with the pump body itself machined to reduce its
> >>  overall thickness, the pulley, when mounted, would be in a 
> different plane
> >>  than the crankshaft drive pulley.... unless I'm missing something. Such a
> >  > misalignment would induce drive belt flip off.  Can you enlighten me
> >  > further? I am trainable.
>
>
>Darius
>
>---------------------------------------------------------------
>
> >  >Darius,
> >  >
> >  >    No change to the pulley. The unit is just made shorter by
> >machining the body back and machining out for the bearing and
> >cutting the axle back and
> >retaining the thing onto which the pulley is bolted. See photo.
>
>Barrie
>_______________________________________________
>Support Team.Net  http://www.team.net/donate.html
>
>Mgb-v8 mailing list
>
>You are subscribed as barrie@look.ca
>
>Mgb-v8@autox.team.net
>http://autox.team.net/mailman/listinfo/mgb-v8

Regards
Barrie

Barrie Robinson
(705) 721-9060
http://www.britishv8.org/MG/BarrieRobinson.htm
http://www.britcot.com 
_______________________________________________
Support Team.Net  http://www.team.net/donate.html

Mgb-v8 mailing list


Mgb-v8@autox.team.net
http://autox.team.net/mailman/listinfo/mgb-v8

<Prev in Thread] Current Thread [Next in Thread>