--===============4803263129285511316==
----__JWM__J5d41d037.76a8aee9S.753e526M
Content-Transfer-Encoding: quoted-printable
Content-Disposition: inline
Is power to be found at wire to the pump? Is pump well earthed? I=
f power is there, have you tapped the pump with a screwdriver handle? =
Have you cleaned the pump's contact books? As for doors, easiest wa=
y is to make a cardboard template of the doors before installing the pan=
els. If doors are already in place, try snipping heads off a dozen num=
ber four finishing nails to make them about 3/4 inch long. Prise back t=
he panel, slip a nail into each of the old screw holes, press the panel =
back against the nails. That will mark about where the holes go, and the=
n you have some guidance for drilling. This I have done successfully. =
Something I have not done, but might be worth a try would be to clamp th=
e hardware to the side curtains, then have someone hold them in place ag=
ainst canvas top, the other curtain, and the windscreen. You, inside the=
car, might be able to set the hardware against the panels and mark the =
holes for drilling. Using a small soldering iron's tip to melt a hole =
in vinyl will reduce the tendency of the vinyl to tear when drill goes t=
hrough.Bob =
---------- Original Message ----------
From: "Gable, Gerry" <GABLEG@ecu.edu>
To: "mg-t@autox.team.net" <mg-t@autox.team.net>
Subject: [Mg-t] TC start up
Date: Sat, 9 Jul 2016 01:32:49 +0000
Tried to start the TC today. Cranks gut no gas. check the obvious, but =
still no pumping. Looking for progression list to follow. Also looking=
for a way to locate the holes on the panels (for the side screen and do=
or hardware) in that the panels cover the existing holes and t-nuts.
Thanks
Hap
----__JWM__J5d41d037.76a8aee9S.753e526M
Content-Transfer-Encoding: quoted-printable
Content-Disposition: inline
<html><div><br> Is power to be found at wire to the pump?</d=
iv><div> Is pump well earthed?</div><div> If pow=
er is there, have you tapped the pump with a screwdriver handle?</div><d=
iv> Have you cleaned the pump's contact books? </div><d=
iv> </div><div> As for doors, easiest way is to m=
ake a cardboard template of the doors before installing the panels.</div=
><div> If doors are already in place, try snipping heads off=
a dozen number four finishing nails to make them about 3/4 inch long. &=
nbsp;Prise back the panel, slip a nail into each of the old screw holes,=
press the panel back against the nails. That will mark about where the =
holes go, and then you have some guidance for drilling. This I have done=
successfully.</div><div> Something I have not done, but mig=
ht be worth a try would be to clamp the hardware to the side curtains, t=
hen have someone hold them in place against canvas top, the other curtai=
n, and the windscreen. You, inside the car, might be able to set the har=
dware against the panels and mark the holes for drilling. </div><di=
v> Using a small soldering iron's tip to melt a hole in vinyl will=
reduce the tendency of the vinyl to tear when drill goes through.</div>=
<div>Bob</div><div> </div><div><br>---------- Original Message ----=
------<br>From: "Gable, Gerry" <GABLEG@ecu.edu><br>To: "mg-t@autox=
.team.net" <mg-t@autox.team.net><br>Subject: [Mg-t] TC start up<br=
>Date: Sat, 9 Jul 2016 01:32:49 +0000<br><br></p><div style=3D"direction=
: ltr; font-family: Tahoma; color: #000000; font-size: 10pt;">Tried to s=
tart the TC today. Cranks gut no gas. check the obvious, but still=
no pumping. Looking for progression list to follow. Also lo=
oking for a way to locate the holes on the panels (for the side screen a=
nd door hardware) in that the panels cover the existing holes and t-nuts=
.<br> Thanks<br> Hap </div></html>
----__JWM__J5d41d037.76a8aee9S.753e526M--
--===============4803263129285511316==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
______________________________________________
Mg-t@autox.team.net
Archive: http://www.team.net/archive
--===============4803263129285511316==--
|