This is a multipart message in MIME format.
--===============3591760374303301232==
boundary="----=_NextPart_000_000B_01D7E4F6.382474C0"
Content-Language: en-ca
This is a multipart message in MIME format.
------=_NextPart_000_000B_01D7E4F6.382474C0
charset="us-ascii"
Content-Transfer-Encoding: 7bit
Simon, so glad the clutch issue is behind you. You may recall from my
clutch saga a few years ago that the replacement parts I received were the
issue, although in my case it was the clutch disc. So I think we must all
be wary of replacement clutches - measure everything and compare old to new.
I am told there are companies that will re-face a pressure plate. Perhaps
this is a better option, although on a high mileage item, weakened springs
may be an issue. I have never run across that myself.
So just get in and drive it!
Cheers, Mirek
From: Healeys <healeys-bounces@autox.team.net> On Behalf Of Simon Lachlan
via Healeys
Sent: November 29, 2021 7:32 AM
To: 'Healeys' <healeys@autox.team.net>
Subject: [Healeys] Update on clutch woes
I received a lot of help and advice with regard to the clutch problem on my
MkII BT7 for which, again, many thanks.
Here's where we are:-
1) I replaced both master and slave cylinders and even converted the former
to having an adjustable push rod which, mercifully, I did not have to use.
No change.
2) I bled the system more times than I've hot dinners, as they say. No
change.
3) I had the gearbox out and back 3 - or was it 4? - times. Centring that
thing to a nanomillimetere if there is such a thing. No change except to
blood pressure.
4) I had fairly fruitless discussions with the supplier who assured me that
"Nothing like this has happened before". No comment will be issued at this
juncture as the lawyers say.
5) I gave up on the new kit and decided that the new clutch cover, being
10+mm higher in the centre than the old, was the likely culprit.
It was indeed the culprit. Restoring the old cover cured the problem 100%.
6) I'd only swapped the clutch in the first place because I had to remove
the gearbox for an overdrive issue. On inspection the old clutch parts
looked pretty good and, while you're in there...
However, new clutch feels better than the old which is good.
7) The supplier refunded me in full thus let me keep the plate and bearing
for free which was some compensation.
Lightened flywheel by 14.5% off. Gives a nice feel. Not a huge difference
but more responsive. I'm pleased with it.
The overdrive pressure issue was solved by an uprated accumulator and other
related bits.
You may recall that the pump would not go back in, despite my best efforts?
I thought I must be doing something wrong but gave up in the end and drove
the OD and box up to OD Spares. Dave put in a new front casing as someone -
NOT me - had used some "Plastic Padding" (JB Weld?) in the area at the top
of the pump's travel. I presume to reline a scored bore. Anyhow, somehow or
other, that stuff prevented my getting the pump back up the last few mm. So,
in effect, that half of the OD has been rebuilt.
And it works!
I'd not had the car on the road until yesterday as I'd been waiting for the
return of my handbrake from the platers. That's back in and looks much
better than before. I even managed to adjust the handbrake cable as,
miraculously, it was all greased and nothing was jammed on the threaded rod.
What next?
Simon
------=_NextPart_000_000B_01D7E4F6.382474C0
charset="us-ascii"
Content-Transfer-Encoding: quoted-printable
<html xmlns:v=3D"urn:schemas-microsoft-com:vml" =
xmlns:o=3D"urn:schemas-microsoft-com:office:office" =
xmlns:w=3D"urn:schemas-microsoft-com:office:word" =
xmlns:m=3D"http://schemas.microsoft.com/office/2004/12/omml"; =
xmlns=3D"http://www.w3.org/TR/REC-html40";><head><meta =
http-equiv=3DContent-Type content=3D"text/html; =
charset=3Dus-ascii"><meta name=3DGenerator content=3D"Microsoft Word 15 =
(filtered medium)"><style><!--
/* Font Definitions */
@font-face
{font-family:"Cambria Math";
panose-1:2 4 5 3 5 4 6 3 2 4;}
@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0cm;
font-size:11.0pt;
font-family:"Calibri",sans-serif;
mso-fareast-language:EN-US;}
span.EmailStyle20
{mso-style-type:personal-reply;
font-family:"Calibri",sans-serif;
color:windowtext;}
.MsoChpDefault
{mso-style-type:export-only;
font-size:10.0pt;}
@page WordSection1
{size:612.0pt 792.0pt;
margin:72.0pt 72.0pt 72.0pt 72.0pt;}
div.WordSection1
{page:WordSection1;}
--></style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext=3D"edit" spidmax=3D"1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext=3D"edit">
<o:idmap v:ext=3D"edit" data=3D"1" />
</o:shapelayout></xml><![endif]--></head><body lang=3DEN-CA =
link=3D"#0563C1" vlink=3D"#954F72" style=3D'word-wrap:break-word'><div =
class=3DWordSection1><p class=3DMsoNormal>Simon, so glad the clutch =
issue is behind you. You may recall from my clutch saga a few =
years ago that the replacement parts I received were the issue, although =
in my case it was the clutch disc. So I think we must all be wary =
of replacement clutches – measure everything and compare old to =
new. I am told there are companies that will re-face a pressure =
plate. Perhaps this is a better option, although on a high mileage =
item, weakened springs may be an issue. I have never run across =
that myself.<o:p></o:p></p><p class=3DMsoNormal><o:p> </o:p></p><p =
class=3DMsoNormal>So just get in and drive it!<o:p></o:p></p><p =
class=3DMsoNormal><o:p> </o:p></p><p class=3DMsoNormal>Cheers, =
Mirek<o:p></o:p></p><p class=3DMsoNormal><o:p> </o:p></p><div><div =
style=3D'border:none;border-top:solid #E1E1E1 1.0pt;padding:3.0pt 0cm =
0cm 0cm'><p class=3DMsoNormal><b><span lang=3DEN-US =
style=3D'mso-fareast-language:EN-CA'>From:</span></b><span lang=3DEN-US =
style=3D'mso-fareast-language:EN-CA'> Healeys =
<healeys-bounces@autox.team.net> <b>On Behalf Of </b>Simon Lachlan =
via Healeys<br><b>Sent:</b> November 29, 2021 7:32 AM<br><b>To:</b> =
'Healeys' <healeys@autox.team.net><br><b>Subject:</b> [Healeys] =
Update on clutch woes<o:p></o:p></span></p></div></div><p =
class=3DMsoNormal><o:p> </o:p></p><p class=3DMsoNormal><span =
lang=3DEN-GB>I received a lot of help and advice with regard to the =
clutch problem on my MkII BT7 for which, again, many =
thanks.<o:p></o:p></span></p><p class=3DMsoNormal><span =
lang=3DEN-GB>Here’s where we are:-<o:p></o:p></span></p><p =
class=3DMsoNormal><span lang=3DEN-GB>1) I replaced both master and slave =
cylinders and even converted the former to having an adjustable push rod =
which, mercifully, I did not have to use. No =
change.<o:p></o:p></span></p><p class=3DMsoNormal><span lang=3DEN-GB>2) =
I bled the system more times than I’ve hot dinners, as they say. =
No change.<o:p></o:p></span></p><p class=3DMsoNormal><span =
lang=3DEN-GB>3) I had the gearbox out and back 3 - or was it 4? – =
times. Centring that thing to a nanomillimetere if there is such a =
thing. No change except to blood pressure.<o:p></o:p></span></p><p =
class=3DMsoNormal><span lang=3DEN-GB>4) I had fairly fruitless =
discussions with the supplier who assured me that “Nothing like =
this has happened before”. No comment will be issued at this =
juncture as the lawyers say.<o:p></o:p></span></p><p =
class=3DMsoNormal><span lang=3DEN-GB>5) I gave up on the new kit and =
decided that the new clutch cover, being 10+mm higher in the centre than =
the old, was the likely culprit.<o:p></o:p></span></p><p =
class=3DMsoNormal><span lang=3DEN-GB>It was indeed the culprit. =
Restoring the old cover cured the problem 100%.<o:p></o:p></span></p><p =
class=3DMsoNormal><span lang=3DEN-GB>6) I’d only swapped the =
clutch in the first place because I had to remove the gearbox for an =
overdrive issue. On inspection the old clutch parts looked pretty good =
and, while you’re in there…..<o:p></o:p></span></p><p =
class=3DMsoNormal><span lang=3DEN-GB>However, new clutch feels better =
than the old which is good.<o:p></o:p></span></p><p =
class=3DMsoNormal><span lang=3DEN-GB>7) The supplier refunded me in full =
thus let me keep the plate and bearing for free which was some =
compensation.<o:p></o:p></span></p><p class=3DMsoNormal><span =
lang=3DEN-GB><o:p> </o:p></span></p><p class=3DMsoNormal><span =
lang=3DEN-GB>Lightened flywheel by 14.5% off. Gives a nice feel. Not a =
huge difference but more responsive. I’m pleased with =
it.<o:p></o:p></span></p><p class=3DMsoNormal><span =
lang=3DEN-GB><o:p> </o:p></span></p><p class=3DMsoNormal><span =
lang=3DEN-GB>The overdrive pressure issue was solved by an uprated =
accumulator and other related bits.<o:p></o:p></span></p><p =
class=3DMsoNormal><span lang=3DEN-GB>You may recall that the pump would =
not go back in, despite my best efforts? I thought I must be doing =
something wrong but gave up in the end and drove the OD and box up to OD =
Spares. Dave put in a new front casing as someone – NOT me – =
had used some “Plastic Padding” (JB Weld?) in the area at =
the top of the pump’s travel. I presume to reline a scored bore. =
Anyhow, somehow or other, that stuff prevented my getting the pump back =
up the last few mm. So, in effect, that half of the OD has been =
rebuilt.<o:p></o:p></span></p><p class=3DMsoNormal><span =
lang=3DEN-GB>And it works!<o:p></o:p></span></p><p =
class=3DMsoNormal><span lang=3DEN-GB><o:p> </o:p></span></p><p =
class=3DMsoNormal><span lang=3DEN-GB>I’d not had the car on the =
road until yesterday as I’d been waiting for the return of my =
handbrake from the platers. That’s back in and looks much better =
than before. I even managed to adjust the handbrake cable as, =
miraculously, it was all greased and nothing was jammed on the threaded =
rod. <o:p></o:p></span></p><p class=3DMsoNormal><span =
lang=3DEN-GB><o:p> </o:p></span></p><p class=3DMsoNormal><span =
lang=3DEN-GB>What next?<o:p></o:p></span></p><p class=3DMsoNormal><span =
lang=3DEN-GB>Simon<o:p></o:p></span></p><p class=3DMsoNormal><span =
lang=3DEN-GB><o:p> </o:p></span></p><p class=3DMsoNormal><span =
lang=3DEN-GB><o:p> </o:p></span></p></div></body></html>
------=_NextPart_000_000B_01D7E4F6.382474C0--
--===============3591760374303301232==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============3591760374303301232==--
|