Kees,
What's flower paper?
Cheers,
Bob Haskell
Austin Healey 3000 BN7/BT7 registrar
On 5/10/21 11:48 AM, Kees Oudesluijs via Healeys wrote:
> Richard,
>
> Rebuilding SU-pumps is therapeutic and satisfying. I started years ago
> after I retired. I still discover new things about them and keep
> developing the technique and methods.
> I always prefer to keep the 3-layer diaphragm as it is far superior to
> the later 2 or even single layer ones. As long as all three layers are
> intact, reasonably supple, not cracked and can be (very carefully)
> separated from each other without damage they are usually OK. When
> cleaned (brake cleaner) and dried I dust them with a little talcum
> powder to prevent them from sticking in the future and keep the rubber
> in good condition. In the past I used some rubber grease. I still have
> perfect original diaphragms from pumps that were fitted in the '50's.
> One thing which is important is to take care with the Bakelite bridge.
> Do not overtighten the fixing screws as the Bakelite is rather brittle
> and cracks easily. However the plus side is that Bakelite can be
> glued, and if bits are missing reconstructed, very well using araldite
> or any other suitable epoxy glue. Same for the cap. It will leave a
> very strong and lasting repair.
> Points are usually fit for sanding the worst pitting followed by
> polishing them with flower paper. Old point may be preferable to new
> points, the old ones are probably a better quality. They hardly wear.
> The main reason the SU-pumps are giving up is lack of use as electric
> corrosion between the points will stop them working. I have done more
> than 160.000miles in my first Jensen-Healey and never had one problem
> with the fuel pump. Even after I laid up the car for about 10 years it
> would still pump the fuel on my yearly start up of the engine. After
> that it was left to its own devices and when I took it out in 2008 to
> fit in my present J-H it failed! I took it apart, cleaned, inspected
> it, polished the points and rebuild it with all its original
> components bar the seals for fuel hose connectors. It has been working
> flawlessly ever since and that was needed was a cleaning of the
> points. Earlier I replaced the capacitor with a transil
> (bi-directional Zener diode), 1.5 KE18CA. I now keep the capacitor and
> fit the transil in parallel with it. It will decrease sparking
> tremendously.
> In very old pumps single instead of double points are fitted and often
> no capacitor is fitted at all from the factory. When rebuilding these
> units I always fit a transil with or without a capacitor to protect
> the points.
> If you want to carry a spare fuel pump, do not use an SU-pump. The
> points will corrode in the boot after some time and it will fail you
> when you need it. Better to get one of those $15 simple Facet fuel
> pumps. They are crude, make a lot of noise but will get you home.
> Cheers,
> Kees
>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
>
> Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive
>
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/rchaskell@earthlink.net
>
_______________________________________________
Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
|