This is a multi-part message in MIME format.
--===============4129371003399871772==
boundary="----=_NextPart_000_000E_01D5D462.F00C5040"
This is a multi-part message in MIME format.
------=_NextPart_000_000E_01D5D462.F00C5040
charset="us-ascii"
Content-Transfer-Encoding: 7bit
Hello,
Has anyone experienced a problem fitting the steering wheel onto the splined
steering shaft? I can get the steering wheel hub to go onto the shaft the
length of the collet but then it hits a dead stop. I have checked both the
male and female splines and there are no obvious problems. The steering
wheel is from a Mk 1 BT7 and the steering box is from a BJ7 and they have
never been together before. The fit should be loose enough to allow the hub
to slide on the shaft but that doesn't seem to be the case. It seems like
either the OD of the shaft to too large or the ID of the hub too small.
Any help is appreciated.... Harold
------=_NextPart_000_000E_01D5D462.F00C5040
charset="us-ascii"
Content-Transfer-Encoding: quoted-printable
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META content=3D"text/html; charset=3Dus-ascii" =
http-equiv=3DContent-Type>
<META name=3DGENERATOR content=3D"MSHTML 11.00.10570.1001"></HEAD>
<BODY>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D142475423-26012020>Hello,</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D142475423-26012020></SPAN></FONT> </DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN class=3D142475423-26012020>Has =
anyone=20
experienced a problem fitting the steering wheel onto the splined =
steering=20
shaft? I can get the steering wheel hub to go onto the shaft the length =
of the=20
collet but then it hits a dead stop. I have checked both the male and =
female=20
splines and there are no obvious problems. The steering wheel is from a =
Mk 1 BT7=20
and the steering box is from a BJ7 and they have never been together =
before. The=20
fit should be loose enough to allow the hub to slide on the shaft but =
that=20
doesn't seem to be the case. It seems like either the OD of the shaft to =
too=20
large or the ID of the hub too small.</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D142475423-26012020></SPAN></FONT> </DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN class=3D142475423-26012020>Any =
help is=20
appreciated.... Harold</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D142475423-26012020></SPAN></FONT> </DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D142475423-26012020></SPAN></FONT> </DIV></BODY></HTML>
------=_NextPart_000_000E_01D5D462.F00C5040--
--===============4129371003399871772==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============4129371003399871772==--
|