--===============5112738840531822051==
boundary="----=_Part_389707829_147076933.1578883840987"
------=_Part_389707829_147076933.1578883840987
Content-Transfer-Encoding: quoted-printable
Yes me too.
Changed out my oil pan gasket for a newer silicone one, and as that drain n=
otch had not been cut out oil pressure went through the roof. Had to drop t=
he pan again and make a notch.rg
----- Original Message -----
From: John Harper <ah100register@gmail.com>
To: David Nock <healeydoc@sbcglobal.net>
Cc: Healeys <healeys@autox.team.net>
Sent: Sun, 12 Jan 2020 15:30:29 -0700 (MST)
Subject: Re: [Healeys] Oil Pressure Relief Valve Question
David
I can add a similar problem to that which you identified where there were 1=
00 sump gaskets on the market that did not a have a hole where the oil behi=
nd the valve could get away resulting in the relief valve not operate corr=
ectly.
If the valve did not 'relief' then oil pressure could rise way above the sa=
fe reading. This could cause the pump to have to work harder and the stain =
on the pump, pump shaft and cam shaft could cause damage.
Best regards
On Sun, 12 Jan 2020 at 19:21, David Nock <healeydoc@sbcglobal.net> wrote:
The spring should fit into the hole in the plug and the valve. There is a b=
leed hole on the back side of the valve that drains back int the oil pan. I=
t sit in the in debt of the oil pan. I have seen some alloy pans that block=
the hole. Also have seen people use excessive silicone and plu the hole up=
.=20
David Nock
Sent from my iPhone
On Jan 12, 2020, at 9:41 AM, jpaynepbr@cox.net wrote:
=EF=BB=BFMy recently rebuilt AH 3000 with new oil pump is putting out 100 p=
si of oil pressure at startup and is at an easy 50 to 60 psi at idle when h=
eated up. It is my understanding that the oil pressure release valve is set=
to not exceed 60 psi? I pulled it out, and my question is, is the spring s=
upposed to sit down inside the machined hole in the plug or is the spring s=
upposed to sit on the lip of the plug and not go down into the hole.=20
<image001.jpg>
Jonas From: Jonas Payne <jpayne@jpaynepbr.onmicrosoft.com>=20
Sent: Sunday, January 12, 2020 9:32 AM
To: Jonas Payne <jpayne@jpaynepbr.onmicrosoft.com>
Subject: Pic=20
Get Outlook for Android_______________________________________________
Archive: http://www.team.net/pipermail/healeyshttp://autox.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
@sbcglobal.net
_______________________________________________
Archive: http://www.team.net/pipermail/healeyshttp://autox.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
ster@gmail.com
--=20
Best wishes
John Harper
AHC UK 100 Register Secretary
------=_Part_389707829_147076933.1578883840987
Content-Transfer-Encoding: quoted-printable
<html><head><style> body {height: 100%; color:#000000; font-size:12pt; font=
-family:arial,helvetica,sans-serif;}</style></head><body><div>Yes me too.<b=
r></div><div>Changed out my oil pan gasket for a newer silicone one, and as=
that drain notch had not been cut out oil pressure went through the roof. =
Had to drop the pan again and make a notch.<br data-mce-bogus=3D"1"></div><=
div>rg<br data-mce-bogus=3D"1"></div><div><br></div><div>----- Original Mes=
sage -----<br>From: John Harper <ah100register@gmail.com><br>To: Davi=
d Nock <healeydoc@sbcglobal.net><br>Cc: Healeys <healeys@autox.tea=
m.net><br>Sent: Sun, 12 Jan 2020 15:30:29 -0700 (MST)<br>Subject: Re: [H=
ealeys] Oil Pressure Relief Valve Question<br></div><div><br></div><div dir=
=3D"ltr">David<div><br></div><div>I can add a similar problem to that which=
you identified where there were 100 sump gaskets on the market that did no=
t a have a hole where the oil behind the valve could get away re=
sulting in the relief valve not operate correctly.</div><div><br></div=
><div>If the valve did not 'relief' then oil pressure could rise way above =
the safe reading. This could cause the pump to have to work harder and the =
stain on the pump, pump shaft and cam shaft could cause damage.</div><div><=
br></div><div>Best regards</div></div><div><br></div><div class=3D"gmail_qu=
ote"><div dir=3D"ltr" class=3D"gmail_attr">On Sun, 12 Jan 2020 at 19:21, Da=
vid Nock <<a href=3D"mailto:healeydoc@sbcglobal.net"; target=3D"_blank" d=
ata-mce-href=3D"mailto:healeydoc@sbcglobal.net";>healeydoc@sbcglobal.net</a>=
> wrote:<br></div><blockquote class=3D"gmail_quote" style=3D"margin: 0px=
0px 0px 0.8ex; border-left: 1px solid #cccccc; padding-left: 1ex;" data-mc=
e-style=3D"margin: 0px 0px 0px 0.8ex; border-left: 1px solid #cccccc; paddi=
ng-left: 1ex;"><div dir=3D"auto">The spring should fit into the hole in the=
plug and the valve. <div>There is a bleed hole on the back side of th=
e valve that drains back int the oil pan. It sit in the in debt of the oil =
pan. I have seen some alloy pans that block the hole. Also have seen people=
use excessive silicone and plu the hole up. <br><div><br></div><div d=
ir=3D"ltr"><div>David Nock</div><div><br></div>Sent from my iPhone</div><di=
v dir=3D"ltr"><br><blockquote>On Jan 12, 2020, at 9:41 AM, <a href=3D"mailt=
o:jpaynepbr@cox.net" target=3D"_blank" data-mce-href=3D"mailto:jpaynepbr@co=
x.net">jpaynepbr@cox.net</a> wrote:<br><div><br></div></blockquote></div><b=
lockquote><div dir=3D"ltr">=EF=BB=BF<div><p class=3D"MsoNormal">My recently=
rebuilt AH 3000 with new oil pump is putting out 100 psi of oil pressure a=
t startup and is at an easy 50 to 60 psi at idle when heated up.<span data-=
mce-style=3D"text-decoration: underline;" style=3D"text-decoration: underli=
ne;"></span><span data-mce-style=3D"text-decoration: underline;" style=3D"t=
ext-decoration: underline;"></span></p><p class=3D"MsoNormal"><span data-mc=
e-style=3D"text-decoration: underline;" style=3D"text-decoration: underline=
;"></span> <span data-mce-style=3D"text-decoration: underline;" style=
=3D"text-decoration: underline;"></span></p><p class=3D"MsoNormal">It is my=
understanding that the oil pressure release valve is set to not exceed 60 =
psi?<span data-mce-style=3D"text-decoration: underline;" style=3D"text-deco=
ration: underline;"></span><span data-mce-style=3D"text-decoration: underli=
ne;" style=3D"text-decoration: underline;"></span></p><p class=3D"MsoNormal=
"><span data-mce-style=3D"text-decoration: underline;" style=3D"text-decora=
tion: underline;"></span> <span data-mce-style=3D"text-decoration: und=
erline;" style=3D"text-decoration: underline;"></span></p><p class=3D"MsoNo=
rmal">I pulled it out, and my question is, is the spring supposed to sit do=
wn inside the machined hole in the plug or is the spring supposed to sit on=
the lip of the plug and not go down into the hole.<span data-mce-style=3D"=
text-decoration: underline;" style=3D"text-decoration: underline;"></span><=
span data-mce-style=3D"text-decoration: underline;" style=3D"text-decoratio=
n: underline;"></span></p><p class=3D"MsoNormal"><span data-mce-style=3D"te=
xt-decoration: underline;" style=3D"text-decoration: underline;"></span>&nb=
sp;<span data-mce-style=3D"text-decoration: underline;" style=3D"text-decor=
ation: underline;"></span></p><p class=3D"MsoNormal"><br></p><div><image=
001.jpg></div><span data-mce-style=3D"text-decoration: underline;" style=
=3D"text-decoration: underline;"></span><span data-mce-style=3D"text-decora=
tion: underline;" style=3D"text-decoration: underline;"></span><p><br></p><=
p class=3D"MsoNormal">Jonas<span data-mce-style=3D"text-decoration: underli=
ne;" style=3D"text-decoration: underline;"></span><span data-mce-style=3D"t=
ext-decoration: underline;" style=3D"text-decoration: underline;"></span></=
p><p class=3D"MsoNormal"><span data-mce-style=3D"text-decoration: underline=
;" style=3D"text-decoration: underline;"></span> <span data-mce-style=
=3D"text-decoration: underline;" style=3D"text-decoration: underline;"></sp=
an></p><p class=3D"MsoNormal"><span data-mce-style=3D"text-decoration: unde=
rline;" style=3D"text-decoration: underline;"></span> <span data-mce-s=
tyle=3D"text-decoration: underline;" style=3D"text-decoration: underline;">=
</span></p><div><div style=3D"border-right: none; border-bottom: none; bord=
er-left: none; border-top: 1pt solid #e1e1e1; padding: 3pt 0in 0in;" data-m=
ce-style=3D"border-right: none; border-bottom: none; border-left: none; bor=
der-top: 1pt solid #e1e1e1; padding: 3pt 0in 0in;"><p class=3D"MsoNormal"><=
b>From:</b> Jonas Payne <<a href=3D"mailto:jpayne@jpaynepbr.onmicrosoft.=
com" target=3D"_blank" data-mce-href=3D"mailto:jpayne@jpaynepbr.onmicrosoft=
.com">jpayne@jpaynepbr.onmicrosoft.com</a>> <br><b>Sent:</b> Sunday, Jan=
uary 12, 2020 9:32 AM<br><b>To:</b> Jonas Payne <<a href=3D"mailto:jpayn=
e@jpaynepbr.onmicrosoft.com" target=3D"_blank" data-mce-href=3D"mailto:jpay=
ne@jpaynepbr.onmicrosoft.com">jpayne@jpaynepbr.onmicrosoft.com</a>><br><=
b>Subject:</b> Pic<span data-mce-style=3D"text-decoration: underline;" styl=
e=3D"text-decoration: underline;"></span><span data-mce-style=3D"text-decor=
ation: underline;" style=3D"text-decoration: underline;"></span></p></div><=
/div><p class=3D"MsoNormal"><span data-mce-style=3D"text-decoration: underl=
ine;" style=3D"text-decoration: underline;"></span> <span data-mce-sty=
le=3D"text-decoration: underline;" style=3D"text-decoration: underline;"></=
span></p><p class=3D"MsoNormal" style=3D"background: white;" data-mce-style=
=3D"background: white;"><span style=3D"color: #212121;" data-mce-style=3D"c=
olor: #212121;"><br></span></p><div><br></div><div id=3D"gmail-m_3910667989=
44367873ms-outlook-mobile-signature"><div><p class=3D"MsoNormal"><span data=
-mce-style=3D"text-decoration: underline;" style=3D"text-decoration: underl=
ine;"></span> <span data-mce-style=3D"text-decoration: underline;" sty=
le=3D"text-decoration: underline;"></span></p></div><p class=3D"MsoNormal">=
Get <a href=3D"https://aka.ms/ghei36"; target=3D"_blank" data-mce-href=3D"ht=
tps://aka.ms/ghei36">Outlook for Android</a><span data-mce-style=3D"text-de=
coration: underline;" style=3D"text-decoration: underline;"></span><span da=
ta-mce-style=3D"text-decoration: underline;" style=3D"text-decoration: unde=
rline;"></span></p></div></div><span>______________________________________=
_________</span><br><span>Support Team.Net <a href=3D"http://www.team.net/d=
onate.html" target=3D"_blank" data-mce-href=3D"http://www.team.net/donate.h=
tml">http://www.team.net/donate.html</a></span><br><span>Suggested annual d=
onation $12.75</span><br><span></span><br><span>Archive: <a href=3D"h=
ttp://www.team.net/pipermail/healeys" target=3D"_blank" data-mce-href=3D"ht=
tp://www.team.net/pipermail/healeys">http://www.team.net/pipermail/healeys<=
/a><a href=3D"http://autox.team.net/archive"; target=3D"_blank" data-mce-hre=
f=3D"http://autox.team.net/archive";>http://autox.team.net/archive</a></span=
><br><span></span><br><span><a href=3D"mailto:Healeys@autox.team.net"; targe=
t=3D"_blank" data-mce-href=3D"mailto:Healeys@autox.team.net";>Healeys@autox.=
team.net</a></span><br><span><a href=3D"http://autox.team.net/mailman/listi=
nfo/healeys" target=3D"_blank" data-mce-href=3D"http://autox.team.net/mailm=
an/listinfo/healeys">http://autox.team.net/mailman/listinfo/healeys</a></sp=
an><br><span></span><br><span>Unsubscribe/Manage: <a href=3D"http://autox.t=
eam.net/mailman/options/healeys/healeydoc@sbcglobal.net" target=3D"_blank" =
data-mce-href=3D"http://autox.team.net/mailman/options/healeys/healeydoc@sb=
cglobal.net">http://autox.team.net/mailman/options/healeys/healeydoc@sbcglo=
bal.net</a></span><br><span></span><br></div></blockquote></div></div>_____=
__________________________________________<br><div><br></div>Support Team.N=
et <a href=3D"http://www.team.net/donate.html"; rel=3D"noreferrer" target=3D=
"_blank" data-mce-href=3D"http://www.team.net/donate.html";>http://www.team.=
net/donate.html</a><br><div><br></div>Suggested annual donation $12.7=
5<br><div><br></div><br>Archive: <a href=3D"http://www.team.net/pipermail/h=
ealeys" rel=3D"noreferrer" target=3D"_blank" data-mce-href=3D"http://www.te=
am.net/pipermail/healeys">http://www.team.net/pipermail/healeys</a><a href=
=3D"http://autox.team.net/archive"; rel=3D"noreferrer" target=3D"_blank" dat=
a-mce-href=3D"http://autox.team.net/archive";>http://autox.team.net/archive<=
/a><br><div><br></div><a href=3D"mailto:Healeys@autox.team.net"; target=3D"_=
blank" data-mce-href=3D"mailto:Healeys@autox.team.net";>Healeys@autox.team.n=
et</a><br><a href=3D"http://autox.team.net/mailman/listinfo/healeys"; rel=3D=
"noreferrer" target=3D"_blank" data-mce-href=3D"http://autox.team.net/mailm=
an/listinfo/healeys">http://autox.team.net/mailman/listinfo/healeys</a><br>=
<div><br></div><br>Unsubscribe/Manage: <a href=3D"http://autox.team.net/mai=
lman/options/healeys/ah100register@gmail.com" rel=3D"noreferrer" target=3D"=
_blank" data-mce-href=3D"http://autox.team.net/mailman/options/healeys/ah10=
0register@gmail.com">http://autox.team.net/mailman/options/healeys/ah100reg=
ister@gmail.com</a><br><div><br></div></blockquote></div><div><br clear=3D"=
all"></div><div><br></div><div>-- <br></div><div dir=3D"ltr" class=3D"gmail=
_signature"><div dir=3D"ltr">Best wishes<div><br></div><div>John Harper</di=
v><div><br></div><div>AHC UK 100 Register Secretary</div></div></div><div><=
br></div><div><br></div></body></html>
------=_Part_389707829_147076933.1578883840987--
--===============5112738840531822051==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============5112738840531822051==--
|