--===============6903924220374446955==
--000000000000873c7f058a91c335
Curt is correct however, what I do notice, is that that threaded hole's
companion has been welded over.
This will be a problem when it comes to hanging the exhaust system.
M
On Wed, Jun 5, 2019, 2:59 AM Curtis Arndt, <cnaarndt@gmail.com> wrote:
> Mike,
>
> It's for the exhaust hanger.
>
> Cheers,
>
> Curt
>
> On Tue, Jun 4, 2019 at 9:03 PM Michael MacLean <rrengineer.mike@att.net>
> wrote:
>
>> I am finally getting around to installing the leaf springs for my
>> BN2. This is the first time I have put a big Healey together and I got my
>> car as a bare shell., so I wanted to make sure I got this right. Check the
>> photos of the rear left leaf spring at the rear hanger. I have all the
>> hardware that was listed at Moss, including the two jam nuts for the bolt
>> through the body mount. The double ended threaded bolt can only go one way
>> with the jam nuts on one end and the big nut and lock washer on the other.
>> I determined the jam nuts were to take the lateral movement out of the
>> bolt, but leave it loose enough to let the links swing with the movement of
>> the axle. After looking at it, I could have just flipped the whole links
>> and bolts over exposing the jam nuts to the outside. Might have been
>> easier that way, but it wasn't bad.
>> Also look at the third picture. This is just below and behind the
>> leaf spring. There is a captive nut behind the sheet metal of the inner
>> wheel well. You can see it it in the center of the photo. What is this
>> threaded hole for?
>> Mike MacLean
>> _______________________________________________
>> Support Team.Net http://www.team.net/donate.html
>> Suggested annual donation $12.75
>>
>> Archive: http://www.team.net/pipermail/healeys
>> http://autox.team.net/archive
>>
>> Healeys@autox.team.net
>> http://autox.team.net/mailman/listinfo/healeys
>>
>> Unsubscribe/Manage:
>> http://autox.team.net/mailman/options/healeys/cnaarndt@gmail.com
>>
>> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
>
> Archive: http://www.team.net/pipermail/healeys
> http://autox.team.net/archive
>
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/michaelsalter@gmail.com
>
>
--000000000000873c7f058a91c335
Content-Transfer-Encoding: quoted-printable
<div dir=3D"auto">Curt is correct however,=C2=A0 what I do notice, is that =
that threaded hole's companion has been welded over.=C2=A0<div dir=3D"a=
uto">This will be a problem when it comes to hanging the exhaust system.=C2=
=A0<div dir=3D"auto"><br></div><div dir=3D"auto">M</div></div></div><br><di=
v class=3D"gmail_quote"><div dir=3D"ltr" class=3D"gmail_attr">On Wed, Jun 5=
, 2019, 2:59 AM Curtis Arndt, <<a href=3D"mailto:cnaarndt@gmail.com";>cna=
arndt@gmail.com</a>> wrote:<br></div><blockquote class=3D"gmail_quote" s=
tyle=3D"margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div=
dir=3D"ltr">Mike,<div><br></div><div>It's for the exhaust hanger.</div=
><div><br></div><div>Cheers,</div><div><br></div><div>Curt</div></div><br><=
div class=3D"gmail_quote"><div dir=3D"ltr" class=3D"gmail_attr">On Tue, Jun=
4, 2019 at 9:03 PM Michael MacLean <<a href=3D"mailto:rrengineer.mike@a=
tt.net" target=3D"_blank" rel=3D"noreferrer">rrengineer.mike@att.net</a>>=
; wrote:<br></div><blockquote class=3D"gmail_quote" style=3D"margin:0px 0px=
0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div><d=
iv class=3D"m_1567604542317482564gmail-m_1021144893536154854yahoo-style-wra=
p" style=3D"font-family:"times new roman","new york",ti=
mes,serif;font-size:16px"><div>=C2=A0=C2=A0=C2=A0=C2=A0 I am finally gettin=
g around to installing the leaf springs for my BN2.=C2=A0 This is the first=
time I have put a big Healey together and I got my car as a bare shell., s=
o I wanted to make sure I got this right.=C2=A0 Check the photos of the rea=
r left leaf spring at the rear hanger.=C2=A0 I have all the hardware that w=
as listed at Moss, including the two jam nuts for the bolt through the body=
mount.=C2=A0 The double ended threaded bolt can only go one way with the j=
am nuts on one end and the big nut and lock washer on the other.=C2=A0 I de=
termined the jam nuts were to take the lateral movement out of the bolt, bu=
t leave it loose enough to let the links swing with the movement of the axl=
e.=C2=A0 After looking at it, I could have just flipped the whole links and=
bolts over exposing the jam nuts to the outside.=C2=A0 Might have been eas=
ier that way, but it wasn't bad.</div><div>=C2=A0=C2=A0=C2=A0 Also look=
at the third picture.=C2=A0 This is just below and behind the leaf spring.=
=C2=A0 There is a captive nut behind the sheet metal of the inner wheel wel=
l.=C2=A0 You can see it it in the center of the photo.=C2=A0 What is this t=
hreaded hole for?</div><div>Mike MacLean<br></div></div></div>_____________=
__________________________________<br>
rer noreferrer" target=3D"_blank">http://www.team.net/donate.html</a><br>
<br>
Archive: <a href=3D"http://www.team.net/pipermail/healeys"; rel=3D"noreferre=
r noreferrer" target=3D"_blank">http://www.team.net/pipermail/healeys</a> <=
a href=3D"http://autox.team.net/archive"; rel=3D"noreferrer noreferrer" targ=
et=3D"_blank">http://autox.team.net/archive</a><br>
<br>
<a href=3D"mailto:Healeys@autox.team.net"; target=3D"_blank" rel=3D"noreferr=
er">Healeys@autox.team.net</a><br>
<a href=3D"http://autox.team.net/mailman/listinfo/healeys"; rel=3D"noreferre=
r noreferrer" target=3D"_blank">http://autox.team.net/mailman/listinfo/heal=
eys</a><br>
<br>
s/cnaarndt@gmail.com" rel=3D"noreferrer noreferrer" target=3D"_blank">http:=
//autox.team.net/mailman/options/healeys/cnaarndt@gmail.com</a><br>
<br>
</blockquote></div>
_______________________________________________<br>
rer noreferrer" target=3D"_blank">http://www.team.net/donate.html</a><br>
<br>
Archive: <a href=3D"http://www.team.net/pipermail/healeys"; rel=3D"noreferre=
r noreferrer" target=3D"_blank">http://www.team.net/pipermail/healeys</a> <=
a href=3D"http://autox.team.net/archive"; rel=3D"noreferrer noreferrer" targ=
et=3D"_blank">http://autox.team.net/archive</a><br>
<br>
<a href=3D"mailto:Healeys@autox.team.net"; target=3D"_blank" rel=3D"noreferr=
er">Healeys@autox.team.net</a><br>
<a href=3D"http://autox.team.net/mailman/listinfo/healeys"; rel=3D"noreferre=
r noreferrer" target=3D"_blank">http://autox.team.net/mailman/listinfo/heal=
eys</a><br>
<br>
s/michaelsalter@gmail.com" rel=3D"noreferrer noreferrer" target=3D"_blank">=
http://autox.team.net/mailman/options/healeys/michaelsalter@gmail.com</a><b=
r>
<br>
</blockquote></div>
--000000000000873c7f058a91c335--
--===============6903924220374446955==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============6903924220374446955==--
|