Patrick
The relationship between TDC and the marker on the damper are defined by the
crankshaft, not the cam. #1 will be at TDC when the marker lines up even if
there is no camshaft installed.
Assuming the engine is sitting in its normal position (vertical, not lying on
its side on your bench) then the Dots on the cam gear and crank gear (also, the
keyway on the cam and the keyway on the crank) should both be at 12 o'clock
(shop manual A.25, reassembling (2). See fig A21 in the shop manual.)
According to that picture I counted 15 links on the chain between the two dots
(including the lonks on the teeth by the dots). Assuming all that is correct,
The distributer should point to #1.
Good luck.
Ed Reiss
PS: If you need the appropriate shop manual pages I can scan and email them to
you.
________________________________
From: Healeys <healeys-bounces at autox.team.net> on behalf of healeys-request
at autox.team.net <healeys-request at autox.team.net>
Sent: Sunday, February 11, 2018 1:00 PM
To: healeys at autox.team.net
Subject: Healeys Digest, Vol 11, Issue 53
Send Healeys mailing list submissions to
healeys at autox.team.net
To subscribe or unsubscribe via the World Wide Web, visit
http://autox.team.net/mailman/listinfo/healeys
or, via email, send a message with subject or body 'help' to
healeys-request at autox.team.net
You can reach the person managing the list at
healeys-owner at autox.team.net
When replying, please edit your Subject line so it is more specific
than "Re: Contents of Healeys digest..."
Today's Topics:
1. Re: Strange Timing Setting (Per Schoerner)
2. Re: Fw: Re: Emergency brake bracket (WILLIAM B LAWRENCE)
3. Re: Strange Timing Setting (Patrick & Caroline Quinn)
4. Re: Strange Timing Setting (Per Schoerner)
5. Re: Trunk Lock probem BJ8 (Larry Wendland)
6. Re: Strange Timing Setting (WILLIAM B LAWRENCE)
7. Re: Strange Timing Setting (richard mayor)
8. Re: Strange Timing Setting (Darin Graber)
9. Emergency Brake Bracket (Robert Begani)
10. one fewer A-H (RCobb)
11. follow-up: one fewer A-H (RCobb)
----------------------------------------------------------------------
Message: 1
Date: Sat, 10 Feb 2018 20:17:42 +0100
From: Per Schoerner <per at schoerner.se>
To: Patrick & Caroline Quinn <p_cquinn at tpg.com.au>
Cc: healeys at autox.team.net
Subject: Re: [Healeys] Strange Timing Setting
Patrick
You have installed the cam chain incorrectly. I assume you have the workshop
manual. Look in section A.25 for the correct procedure.
Best, Per
Skickat fr?n min iPad
> 10 feb. 2018 kl. 11:35 skrev Patrick & Caroline Quinn <p_cquinn at
> tpg.com.au>:
>
> Greetings
>
> Perhaps someone has come across this before.
>
> About to start the engine in the BN3 after a complete rebuild. The engine is
> a very early C-series six-cylinder and the rebuild included new bearings
> throughout, pistons, sleeves, valves, vernier adjustable timing chain etc.
>
> When setting the timing all the settings were done by the book. Tappets at 12
> thou, the pointer on the timing chain cover is pointing to the notch in the
> harmonic balancer, the gear shaft drive from the oil pump/camshaft is at 20
> to 2 and the offset distributor drive is correct. Number 1 piston is top dead
> centre and the rocker gear is rocking.
>
> Imaging please looking down at the open distributor and it?s a clock face.
> According to the book, the rotor button arm should be at 2 o?clock or firing
> No 1 spark plug.
>
> However the rotor button is a 10 o?clock.
>
> So it?s not 180 degrees out, but 120 degrees.
>
> Of course you could get around it by changing the spark plug leads, but the
> result looks untidy. An alternative is to rotate the geared shaft drive
> clockwise by 120 degrees.
>
> Any suggestions?
>
> Thanks
>
> Patrick Quinn
> Blue Mountains, Australia
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
>
> Healeys at autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/per at
> schoerner.se
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/healeys/attachments/20180210/a68a20fe/attachment-0001.html>
------------------------------
Message: 2
Date: Sat, 10 Feb 2018 21:09:37 +0000
From: WILLIAM B LAWRENCE <ynotink at msn.com>
To: "sbyers at ec.rr.com" <sbyers at ec.rr.com>, David Lodge
<emmgeeteesee at gmail.com>
Cc: Healey List <healeys at autox.team.net>
Subject: Re: [Healeys] Fw: Re: Emergency brake bracket
Message-ID:
<MWHPR19MB11184FDD87FA0DA6794B8AC0A5F10 at
MWHPR19MB1118.namprd19.prod.outlook.com>
To Bob Begani,
If the screw head was drilled off and the drilling was close to center, the
easiest fix is to drill through the old screw starting with a small pilot and
working up to a size near the original bolt size and then run a thread tap
through. I believe these screws are a 5/16" x 24 thread. If the hole is not
aligned perfectly you may sacrifice a little of the thread on one side of the
hole. Worst case is that you end up drilling it out oversize and inserting a
helicoil.
Bill Lawrence
BN1 #554
________________________________
From: Healeys <healeys-bounces at autox.team.net> on behalf of David Lodge
<emmgeeteecee at yahoo.co.uk>
Sent: Saturday, February 10, 2018 6:56:38 AM
To: sbyers at ec.rr.com
Cc: Healey List
Subject: [Healeys] Fw: Re: Emergency brake bracket
Hello Steve,
Forgive my dilapidated memory, but with that and Yahoo Mail being cloaked in
arcane mystery, I forgot to copy this to you, and I'm never sure when my emails
to the group actually arrive where they're intended, but here goes!!!
----- Forwarded message -----
From: David Lodge <emmgeeteecee at yahoo.co.uk>
To: Robert Begani <rfbegani at gmail.com>; David Nock British Car Specialists
<healeydoc at sbcglobal.net>; Brian Drab <bgdrab at eastlink.ca>
Cc: Healey List <healeys at autox.team.net>
Sent: Monday, 5 February 2018, 21:34:18 GMT-8
Subject: Re: [Healeys] Emergency brake bracket
As promised, the latest brain-teaser in my own particular Healey saga!
Three pics of the afflicted area. Note experimental high-tech, temporary
light-green brace (Ahem!)
Hole in chassis welded in, to be ground flat for re-attachment of handbrake
pivot.
Traces of the works weld still visible, so correct location no problem!
..........and meanwhile, in the boot!
On Sunday, 4 February 2018, 21:48, David Lodge <emmgeeteecee at yahoo.co.uk>
wrote:
Thanks, Bob. Hugely helpful! It occurs to me that I should post a photo of my
particular nightmare! Will do tomorrow.
Regards, D, 1965 BJ8
On Sunday, 4 February 2018, 08:16:54 GMT-8, David Nock British Car Specialists
<healeydoc at sbcglobal.net> wrote:
The spacer should slide off. Then pull the carpet back and remove the
driveshaft. Then you can heat the nut to a slight red and remove the broken
bolt with vice grips
David Nock
British Car Specialists
Stockton Ca 95205
209-948-8767
www.britishcarspecialists.com<https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.britishcarspecialists.com%2F&data=02%7C01%7C%7C0bc75a05eb9947d0b3dd08d57059be31%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636538454386993126&sdata=z9q5ToaSC7ie5x1TAf0Pdi%2FDegNk5wwJ4U7nx3b0tyk%3D&reserved=0<http://www.britishcarspecialists.com<https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.britishcarspecialists.com%2F&data=02%7C01%7C%7C0bc75a05eb9947d0b3dd08d57059be31%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636538454386993126&sdata=z9q5ToaSC7ie5x1TAf0Pdi%2FDegNk5wwJ4U7nx3b0tyk%3D&reserved=0>>
Please feel free to view an interview with the Nock's in 2009
Enjoy
www.youtube.com/watch?v=QOTTRYkbQzs<https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3DQOTTRYkbQzs&data=02%7C01%7C%7C0bc75a05eb9947d0b3dd08d57059be31%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636538454386993126&sdata=4WJ%2B4ZI0Yg%2FhIdDKPnGfaGvT4jN32dv9zdzcvDjk%2F9M%3D&reserved=0<http://www.youtube.com/watch?v=QOTTRYkbQzs<https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3DQOTTRYkbQzs&data=02%7C01%7C%7C0bc75a05eb9947d0b3dd08d57059be31%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636538454386993126&sdata=4WJ%2B4ZI0Yg%2FhIdDKPnGfaGvT4jN32dv9zdzcvDjk%2F9M%3D&reserved=0>>
.
.
Sent from my iPad
Hi David:
Just so happens I have the Tunnel available for your viewing pleasure. See
attached photos of the bracket. My emergency brake has not been on the car
for several years as the cable broke. I could not put the brake on the
bracket because the head of one of the screws was drilled out to get it off.
My next project is to get the frozen screw out and then find a reasonable
replacement.
Regards,
Bob Begani
BJ8 67
<IMG_0408.JPG>
<IMG_0409.JPG>
_______________________________________________
Archive:
http://www.team.net/archive<https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.team.net%2Farchive&data=02%7C01%7C%7C0bc75a05eb9947d0b3dd08d57059be31%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636538454386993126&sdata=rl0F1t27IdC%2Fl5JNwl8uZ2AU0pY%2B%2BxTM9vjXyObW1eI%3D&reserved=0>
http://autox.team.net/mailman/listinfo/healeys<https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fautox.team.net%2Fmailman%2Flistinfo%2Fhealeys&data=02%7C01%7C%7C0bc75a05eb9947d0b3dd08d57059be31%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636538454386993126&sdata=USMSwGgKS%2ByOmao%2BrvVIZx7SRayzjb02PxSlQ%2FXpNXY%3D&reserved=0>
_______________________________________________
Archive:
http://www.team.net/archive<https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.team.net%2Farchive&data=02%7C01%7C%7C0bc75a05eb9947d0b3dd08d57059be31%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636538454387149385&sdata=yHgVXjXGOODuJ2GdrDjM8Xh20OK69EmB9qGMGgbhSHU%3D&reserved=0>
http://autox.team.net/mailman/listinfo/healeys<https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fautox.team.net%2Fmailman%2Flistinfo%2Fhealeys&data=02%7C01%7C%7C0bc75a05eb9947d0b3dd08d57059be31%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636538454387149385&sdata=HTqjpKniN898HDmv85L8noQHThE9mOPPk%2BTHMOrO7A0%3D&reserved=0>
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/healeys/attachments/20180210/980d2f82/attachment-0001.html>
------------------------------
Message: 3
Date: Sun, 11 Feb 2018 09:42:59 +1100
From: "Patrick & Caroline Quinn" <p_cquinn at tpg.com.au>
To: "'Per Schoerner'" <per at schoerner.se>
Cc: healeys at autox.team.net
Subject: Re: [Healeys] Strange Timing Setting
Hello Per
I thought about that, but as No 1 is at top dead centre when the pointer is
towards the notch in the harmonic balancer I can?t see how it can be.
Many thanks
Patrick Quinn
From: Per Schoerner [mailto:per at schoerner.se]
Sent: Sunday, 11 February 2018 6:18 AM
To: Patrick & Caroline Quinn
Cc: healeys at autox.team.net
Subject: Re: [Healeys] Strange Timing Setting
Patrick
You have installed the cam chain incorrectly. I assume you have the workshop
manual. Look in section A.25 for the correct procedure.
Best, Per
Skickat fr?n min iPad
10 feb. 2018 kl. 11:35 skrev Patrick & Caroline Quinn <p_cquinn at tpg.com.au>:
Greetings
Perhaps someone has come across this before.
About to start the engine in the BN3 after a complete rebuild. The engine is a
very early C-series six-cylinder and the rebuild included new bearings
throughout, pistons, sleeves, valves, vernier adjustable timing chain etc.
When setting the timing all the settings were done by the book. Tappets at 12
thou, the pointer on the timing chain cover is pointing to the notch in the
harmonic balancer, the gear shaft drive from the oil pump/camshaft is at 20 to
2 and the offset distributor drive is correct. Number 1 piston is top dead
centre and the rocker gear is rocking.
Imaging please looking down at the open distributor and it?s a clock face.
According to the book, the rotor button arm should be at 2 o?clock or firing No
1 spark plug.
However the rotor button is a 10 o?clock.
So it?s not 180 degrees out, but 120 degrees.
Of course you could get around it by changing the spark plug leads, but the
result looks untidy. An alternative is to rotate the geared shaft drive
clockwise by 120 degrees.
Any suggestions?
Thanks
Patrick Quinn
Blue Mountains, Australia
_______________________________________________
Archive: http://www.team.net/archive
Healeys at autox.team.net
http://autox.team.net/mailman/listinfo/healeys
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/healeys/attachments/20180211/4320d706/attachment-0001.html>
------------------------------
Message: 4
Date: Sun, 11 Feb 2018 01:25:16 +0100
From: Per Schoerner <per at schoerner.se>
To: Patrick & Caroline Quinn <p_cquinn at tpg.com.au>
Cc: healeys at autox.team.net
Subject: Re: [Healeys] Strange Timing Setting
Patrick
When you install the chain you should have the key ways of both crankshaft and
camshaft approximately at TDC. This is not the same as having piston 1 at TDC.
Then you should place the bright links of the chain on the marked teeth on the
sprockets and push them home on the shafts. Rather than copying the whole
section A21 I urge you to read it again. I think it?s the TDC thing that you
mixed up.
Best, Per
Skickat fr?n min iPad
> 10 feb. 2018 kl. 23:42 skrev Patrick & Caroline Quinn <p_cquinn at
> tpg.com.au>:
>
> Hello Per
>
> I thought about that, but as No 1 is at top dead centre when the pointer is
> towards the notch in the harmonic balancer I can?t see how it can be.
>
> Many thanks
>
> Patrick Quinn
>
> From: Per Schoerner [mailto:per at schoerner.se]
> Sent: Sunday, 11 February 2018 6:18 AM
> To: Patrick & Caroline Quinn
> Cc: healeys at autox.team.net
> Subject: Re: [Healeys] Strange Timing Setting
>
> Patrick
> You have installed the cam chain incorrectly. I assume you have the workshop
> manual. Look in section A.25 for the correct procedure.
>
> Best, Per
>
> Skickat fr?n min iPad
>
> 10 feb. 2018 kl. 11:35 skrev Patrick & Caroline Quinn <p_cquinn at
> tpg.com.au>:
>
> Greetings
>
> Perhaps someone has come across this before.
>
> About to start the engine in the BN3 after a complete rebuild. The engine is
> a very early C-series six-cylinder and the rebuild included new bearings
> throughout, pistons, sleeves, valves, vernier adjustable timing chain etc.
>
> When setting the timing all the settings were done by the book. Tappets at 12
> thou, the pointer on the timing chain cover is pointing to the notch in the
> harmonic balancer, the gear shaft drive from the oil pump/camshaft is at 20
> to 2 and the offset distributor drive is correct. Number 1 piston is top dead
> centre and the rocker gear is rocking.
>
> Imaging please looking down at the open distributor and it?s a clock face.
> According to the book, the rotor button arm should be at 2 o?clock or firing
> No 1 spark plug.
>
> However the rotor button is a 10 o?clock.
>
> So it?s not 180 degrees out, but 120 degrees.
>
> Of course you could get around it by changing the spark plug leads, but the
> result looks untidy. An alternative is to rotate the geared shaft drive
> clockwise by 120 degrees.
>
> Any suggestions?
>
> Thanks
>
> Patrick Quinn
> Blue Mountains, Australia
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
>
> Healeys at autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/per at
> schoerner.se
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/healeys/attachments/20180211/e045c91f/attachment-0001.html>
------------------------------
Message: 5
Date: Sat, 10 Feb 2018 19:34:56 -0500
From: Larry Wendland <bighealey3k at aim.com>
To: rfbegani at gmail.com, healeys at autox.team.net
Subject: Re: [Healeys] Trunk Lock probem BJ8
Climb inside and have some one you trust close the boot lid and use a
flashlight to see what is going on. Years ago I got inside my boot on my 67 BJ8
to see where the lid seal wasn't contacting the shroud rim so I could adjust
the sheet metal to make contact. I had a problem with road dust collecting in
the trunk (boot) and there were a couple of places where it didn't touch the
seal. Unless you are a realy big person, you should be able to fit inside. Take
pics with a cell phone or digital camera.
Larry
'67 BJ8
-----Original Message-----
From: Robert Begani <rfbegani at gmail.com>
To: healeys <healeys at autox.team.net>
Sent: Sat, Feb 10, 2018 7:12 am
Subject: [Healeys] Trunk Lock probem BJ8
I have the same problem on my BJ8.? I have adjusted it so many times without
success.? Any suggestions.
?
Bob Begani
BJ8 67
_______________________________________________
Archive: http://www.team.net/archive
Healeys at autox.team.net
http://autox.team.net/mailman/listinfo/healeys
------------------------------
Message: 6
Date: Sun, 11 Feb 2018 00:41:55 +0000
From: WILLIAM B LAWRENCE <ynotink at msn.com>
To: Patrick & Caroline Quinn <p_cquinn at tpg.com.au>, 'Per Schoerner'
<per at schoerner.se>
Cc: "healeys at autox.team.net" <healeys at autox.team.net>
Subject: Re: [Healeys] Strange Timing Setting
Message-ID:
<MWHPR19MB1118F9F749AE88B3CA8F1503A5F00 at
MWHPR19MB1118.namprd19.prod.outlook.com>
I don't remember if the mark on the damper is located on the center, fixed,
portion or the outer. rubber suspended, portion. If the latter then maybe the
damper has slipped out of register.
Bill Lawrence
BN1 #554
________________________________
From: Healeys <healeys-bounces at autox.team.net> on behalf of Patrick &
Caroline Quinn <p_cquinn at tpg.com.au>
Sent: Saturday, February 10, 2018 10:42:59 PM
To: 'Per Schoerner'
Cc: healeys at autox.team.net
Subject: Re: [Healeys] Strange Timing Setting
Hello Per
I thought about that, but as No 1 is at top dead centre when the pointer is
towards the notch in the harmonic balancer I can?t see how it can be.
Many thanks
Patrick Quinn
From: Per Schoerner [mailto:per at schoerner.se]
Sent: Sunday, 11 February 2018 6:18 AM
To: Patrick & Caroline Quinn
Cc: healeys at autox.team.net
Subject: Re: [Healeys] Strange Timing Setting
Patrick
You have installed the cam chain incorrectly. I assume you have the workshop
manual. Look in section A.25 for the correct procedure.
Best, Per
Skickat fr?n min iPad
Greetings
Perhaps someone has come across this before.
About to start the engine in the BN3 after a complete rebuild. The engine is a
very early C-series six-cylinder and the rebuild included new bearings
throughout, pistons, sleeves, valves, vernier adjustable timing chain etc.
When setting the timing all the settings were done by the book. Tappets at 12
thou, the pointer on the timing chain cover is pointing to the notch in the
harmonic balancer, the gear shaft drive from the oil pump/camshaft is at 20 to
2 and the offset distributor drive is correct. Number 1 piston is top dead
centre and the rocker gear is rocking.
Imaging please looking down at the open distributor and it?s a clock face.
According to the book, the rotor button arm should be at 2 o?clock or firing No
1 spark plug.
However the rotor button is a 10 o?clock.
So it?s not 180 degrees out, but 120 degrees.
Of course you could get around it by changing the spark plug leads, but the
result looks untidy. An alternative is to rotate the geared shaft drive
clockwise by 120 degrees.
Any suggestions?
Thanks
Patrick Quinn
Blue Mountains, Australia
_______________________________________________
Archive:
http://www.team.net/archive<https://nam01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.team.net%2Farchive&data=02%7C01%7C%7C59d44727cacc4a88db0008d570e3993d%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636539045191578712&sdata=MGcW0f1BvrrzBs0BaTPhxwMPjl6K9uVLjhTzUA4WM4A%3D&reserved=0>
http://autox.team.net/mailman/listinfo/healeys<https://nam01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fautox.team.net%2Fmailman%2Flistinfo%2Fhealeys&data=02%7C01%7C%7C59d44727cacc4a88db0008d570e3993d%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636539045191578712&sdata=IarnGRjFcTzhwvfWunXUtyRMhbtjjgvVYrPzxiF9wuQ%3D&reserved=0>
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/healeys/attachments/20180211/06eecaf6/attachment-0001.html>
------------------------------
Message: 7
Date: Sat, 10 Feb 2018 18:06:02 -0800
From: richard mayor <boyracer466 at gmail.com>
To: Per Schoerner <per at schoerner.se>
Cc: healeys <healeys at autox.team.net>
Subject: Re: [Healeys] Strange Timing Setting
Message-ID:
<CAKkXjqMAMnsva3s-vVPaxU_VgjhbJxtziX7fx4gRjkwqhMVa-w at mail.gmail.com>
Just to add one more thing to this thread, all of the new chains do not
have a "bright" link. So look very carefully at the picture in the manual
and count the links between the dots. This is extremely important as it is
very easy to get it off by even one one tooth. And one tooth, either way,
will have a dramatic effect on engine performance. In either case, it will
be bad.
On Sat, Feb 10, 2018 at 4:25 PM, Per Schoerner <per at schoerner.se> wrote:
> Patrick
> When you install the chain you should have the key ways of both crankshaft
> and camshaft approximately at TDC. This is not the same as having piston 1
> at TDC. Then you should place the bright links of the chain on the marked
> teeth on the sprockets and push them home on the shafts. Rather than
> copying the whole section A21 I urge you to read it again. I think it?s the
> TDC thing that you mixed up.
>
> Best, Per
>
> Skickat fr?n min iPad
>
> 10 feb. 2018 kl. 23:42 skrev Patrick & Caroline Quinn <p_cquinn at tpg.com.au
> >:
>
> Hello Per
>
>
>
> I thought about that, but as No 1 is at top dead centre when the pointer
> is towards the notch in the harmonic balancer I can?t see how it can be.
>
>
>
> Many thanks
>
>
>
> Patrick Quinn
>
>
>
> *From:* Per Schoerner [mailto:per at schoerner.se <per at schoerner.se>]
> *Sent:* Sunday, 11 February 2018 6:18 AM
> *To:* Patrick & Caroline Quinn
> *Cc:* healeys at autox.team.net
> *Subject:* Re: [Healeys] Strange Timing Setting
>
>
>
> Patrick
>
> You have installed the cam chain incorrectly. I assume you have the
> workshop manual. Look in section A.25 for the correct procedure.
>
>
>
> Best, Per
>
> Skickat fr?n min iPad
>
>
> 10 feb. 2018 kl. 11:35 skrev Patrick & Caroline Quinn <p_cquinn at tpg.com.au
> >:
>
> Greetings
>
>
>
> Perhaps someone has come across this before.
>
>
>
> About to start the engine in the BN3 after a complete rebuild. The engine
> is a very early C-series six-cylinder and the rebuild included new bearings
> throughout, pistons, sleeves, valves, vernier adjustable timing chain etc.
>
>
>
> When setting the timing all the settings were done by the book. Tappets at
> 12 thou, the pointer on the timing chain cover is pointing to the notch in
> the harmonic balancer, the gear shaft drive from the oil pump/camshaft is
> at 20 to 2 and the offset distributor drive is correct. Number 1 piston is
> top dead centre and the rocker gear is rocking.
>
>
>
> Imaging please looking down at the open distributor and it?s a clock face.
> According to the book, the rotor button arm should be at 2 o?clock or
> firing No 1 spark plug.
>
>
>
> However the rotor button is a 10 o?clock.
>
>
>
> So it?s not 180 degrees out, but 120 degrees.
>
>
>
> Of course you could get around it by changing the spark plug leads, but
> the result looks untidy. An alternative is to rotate the geared shaft drive
> clockwise by 120 degrees.
>
>
>
> Any suggestions?
>
>
>
> Thanks
>
>
>
> Patrick Quinn
>
> Blue Mountains, Australia
>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
>
> Healeys at autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage: http://autox.team.net/mailman/
> options/healeys/per at schoerner.se
>
>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
>
> Healeys at autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage: http://autox.team.net/mailman/
> options/healeys/boyracer466 at gmail.com
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/healeys/attachments/20180210/38d57457/attachment-0001.html>
------------------------------
Message: 8
Date: Sat, 10 Feb 2018 19:16:19 -0700
From: Darin Graber <dkgraber85 at yahoo.com>
To: Per Schoerner <per at schoerner.se>
Cc: healeys at autox.team.net
Subject: Re: [Healeys] Strange Timing Setting
Yep, the cam timing is off. There should be 15 links between the marks on both
the Cam and the crank pulley.
Sent from my iPhone 6+
> On Feb 10, 2018, at 5:25 PM, Per Schoerner <per at schoerner.se> wrote:
>
> Patrick
> When you install the chain you should have the key ways of both crankshaft
> and camshaft approximately at TDC. This is not the same as having piston 1 at
> TDC. Then you should place the bright links of the chain on the marked teeth
> on the sprockets and push them home on the shafts. Rather than copying the
> whole section A21 I urge you to read it again. I think it?s the TDC thing
> that you mixed up.
>
> Best, Per
>
> Skickat fr?n min iPad
>
>> 10 feb. 2018 kl. 23:42 skrev Patrick & Caroline Quinn <p_cquinn at
>> tpg.com.au>:
>>
>> Hello Per
>>
>> I thought about that, but as No 1 is at top dead centre when the pointer is
>> towards the notch in the harmonic balancer I can?t see how it can be.
>>
>> Many thanks
>>
>> Patrick Quinn
>>
>> From: Per Schoerner [mailto:per at schoerner.se]
>> Sent: Sunday, 11 February 2018 6:18 AM
>> To: Patrick & Caroline Quinn
>> Cc: healeys at autox.team.net
>> Subject: Re: [Healeys] Strange Timing Setting
>>
>> Patrick
>> You have installed the cam chain incorrectly. I assume you have the workshop
>> manual. Look in section A.25 for the correct procedure.
>>
>> Best, Per
>>
>> Skickat fr?n min iPad
>>
>> 10 feb. 2018 kl. 11:35 skrev Patrick & Caroline Quinn <p_cquinn at
>> tpg.com.au>:
>>
>> Greetings
>>
>> Perhaps someone has come across this before.
>>
>> About to start the engine in the BN3 after a complete rebuild. The engine is
>> a very early C-series six-cylinder and the rebuild included new bearings
>> throughout, pistons, sleeves, valves, vernier adjustable timing chain etc.
>>
>> When setting the timing all the settings were done by the book. Tappets at
>> 12 thou, the pointer on the timing chain cover is pointing to the notch in
>> the harmonic balancer, the gear shaft drive from the oil pump/camshaft is at
>> 20 to 2 and the offset distributor drive is correct. Number 1 piston is top
>> dead centre and the rocker gear is rocking.
>>
>> Imaging please looking down at the open distributor and it?s a clock face.
>> According to the book, the rotor button arm should be at 2 o?clock or firing
>> No 1 spark plug.
>>
>> However the rotor button is a 10 o?clock.
>>
>> So it?s not 180 degrees out, but 120 degrees.
>>
>> Of course you could get around it by changing the spark plug leads, but the
>> result looks untidy. An alternative is to rotate the geared shaft drive
>> clockwise by 120 degrees.
>>
>> Any suggestions?
>>
>> Thanks
>>
>> Patrick Quinn
>> Blue Mountains, Australia
>> _______________________________________________
>> Support Team.Net http://www.team.net/donate.html
>> Suggested annual donation $12.75
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>>
>> Healeys at autox.team.net
>> http://autox.team.net/mailman/listinfo/healeys
>>
>> Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/per at
>> schoerner.se
>>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
>
> Healeys at autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/dkgraber85
> at yahoo.com
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/healeys/attachments/20180210/9abc89f0/attachment-0001.html>
------------------------------
Message: 9
Date: Sun, 11 Feb 2018 08:49:05 -0500
From: "Robert Begani" <rfbegani at gmail.com>
To: <healeys at autox.team.net>
Subject: [Healeys] Emergency Brake Bracket
Further to the bracket, as the head was drilled off of the screw which would
not come off, I cut off the remainder with a dremel cutoff wheel, removed
the spacer and applied lots of PB blaster. Using a mini Vise Grip pliers, I
got it to move, applied more PB and more movement. Eventurally, the machine
screw come off. The problem is replacing the screws. All I could obtain is
stainless steel phillips head screws with a much larger head. So off to my
friend George, who measured the existing screw head, put it in the lathe and
determined the angle of the head is 43 degrees, so he slowly shaved off the
sides of the head until it resembled the original screw. Fit perfectly.
Bob Begani
BJ8 67
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/healeys/attachments/20180211/c7022bb8/attachment-0001.html>
------------------------------
Message: 10
Date: Sun, 11 Feb 2018 08:52:36 -0800
From: RCobb <rcobb at sonic.net>
To: healeys at autox.team.net
Subject: [Healeys] one fewer A-H
http://sanfrancisco.cbslocal.com/2018/02/11/atherton-caltrain-strikes-car/
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/healeys/attachments/20180211/7696c8e1/attachment-0001.html>
------------------------------
Message: 11
Date: Sun, 11 Feb 2018 08:58:21 -0800
From: RCobb <rcobb at sonic.net>
To: healeys at autox.team.net
Subject: [Healeys] follow-up: one fewer A-H
The lesson apparently is: Don't blindly follow your GPS...
http://padailypost.com/2018/02/10/caltrain-hits-classic-car-drags-quarter-mile/
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/healeys/attachments/20180211/fad3b622/attachment-0001.html>
------------------------------
Subject: Digest Footer
_______________________________________________
Healeys mailing list
Healeys at autox.team.net
http://autox.team.net/mailman/listinfo/healeys
------------------------------
End of Healeys Digest, Vol 11, Issue 53
***************************************
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/healeys/attachments/20180211/77280180/attachment.html>
|