Ron & Tim,
Remove the screw and attach a slide hammer to the end of the shaft to
remove the shaft from the fork. I wrote an article back in '97 for
team.net's healey web pages, but the site's down. The threads for the
hole on the end of the shaft are 1/4"-28 I believe and about 1" deep.
Be careful with the heat, There are two plastic washers, one on either
side of the fork.
Cheers,
Bob Haskell
AHCA 3000 Mk I registrar
http://www.ciahc.org/registry_3000mk1.php
On 09/27/2015 03:10 PM, Tim Davis BN7 wrote:
> Thanks for the informed response I hope I will be able to avoid some of
> what you have experienced. I now will apply heat to the joint in hopes
> of loosening things up first. I have a few bellhousings so I can
> practice a little, all need the fork bushings to some extent except an
> older one that doesn't have a shaft seal and I didn't want to use that
> type.
> I see the manual calls the mystery screw the "clutch withdrawal fork
> screw" doesn't make much sense unless it's meant to be a joke.
> I hope we'll get some additional informed responses.
>
> Good Luck.
>
> ------------------------------------------------------------------------
> *From: *"Ron Mitchell" <healeyron@yahoo.com>
> *To: *"Tim Davis BN7" <tld6008@mchsi.com>, "Healey List"
> <healeys@autox.team.net>
> *Sent: *Sunday, September 27, 2015 1:52:33 PM
> *Subject: *Re: [Healeys] Clutch fork bushings
>
> I just tried to replace those bushings on my Side Shift Transmission.
> The tapered pin is supposed to be removed from the transmission side
> of the Bell Housing. The only problem is the pin is soft and the pin
> mushroomed larger than the hole in the Fork and Shaft. I ended up
> having to drill the pin from the engine side of the Bell Housing. The
> drill drifted which permitted it to exit on the Trans. side of the fork
> off center. I than cut the end of the pin flush with the fork I was
> then able to extract the remains of the tapered pin out the engine side
> of the BH. Now that the pin was extracted the easy part should be to
> remove the shaft and install new bushings. Not for me. The shaft was
> seized in the fork and after carefully trying to hammer it out I
> determined that I was doing unrepairable harm to the shaft. I was able
> to obtain the correct sized tapered pin from ACE Hardware. I believe it
> was a no. 02 x 2.00 long tapered pin. I inserted the pin. Filed it
> smooth on the engine side of the fork and and am willing to live with
> the slopping bushings. I know this doesn't help but I had to tell
> someone. Wasted two days and ended where I started. No cigar.
>
> If anyone can tell me how to remove the shaft I still have the
> opportunity to do that before attaching the transmission to the engine.
>
> Question? Does anyone know the purpose of the screw in the end of the
> shaft?
>
> Ron Mitchell
> 59 BN6
>
> ------------------------------------------------------------------------
> *From:* Tim Davis BN7 <tld6008@mchsi.com>
> *To:* Healey List <healeys@autox.team.net>
> *Sent:* Sunday, September 27, 2015 1:37 PM
> *Subject:* [Healeys] Clutch fork bushings
>
> I need to replace these on my sideshift transmission. Have it out and
> bellhousing off but before I damage something is the pin referred to as
> "taper pin" driven out from the transmission side through access hole in
> mating surface? Any pointers?
> Another question, Can the throttle crossshaft bushings be replaced with
> the clutch inplace or is this not obstructing access?
>
> TIA
>
> Tim Davis BN7
>
>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
>
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/healeyron@yahoo.com
>
>
>
>
>
>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
>
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/rchaskell@earthlink.net
>
_______________________________________________
Archive: http://www.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
|