healeys
[Top] [All Lists]

Re: [Healeys] Steering Box and Wire Wheel Questions--BJ8

To: Michael Oritt <michael.oritt@gmail.com>, Michael <michael.salter@gmail.com>
Subject: Re: [Healeys] Steering Box and Wire Wheel Questions--BJ8
From: <glemon@neb.rr.com>
Date: Mon, 15 Jun 2015 0:01:24 +0000
Authentication-results: cdptpa-oedge02 smtp.user=glemon@neb.rr.com; auth=pass (LOGIN)
Cc: Austin Healey <healeys@autox.team.net>
Delivered-to: mharc@autox.team.net
Delivered-to: healeys@autox.team.net
Sensitivity: Normal Mon, 15 Jun 2015 0:01:24 +0000
Penrite steering box lube should stop the leak or slow it considerably if not 
completely.  I have read about corn head grease, which sounds like similar 
stuff, but despite being in Nebraska I have more LBC knowledge than tractor so 
it was easier for me to find a source for the penrite.  I used it on my 100 
after I put on a new seal.  Leak went away.

Greg Lemon
---- Michael Oritt <michael.oritt@gmail.com> wrote: 
> Maybe he should just buy some more oil....
> 
> Best--Michael Oritt
> 
> On Sun, Jun 14, 2015 at 6:08 PM, Michael <michael.salter@gmail.com> wrote:
> 
> > Interesting...
> > I have always found that the problem was attributable to corrosion on the
> > rocker shaft where the seal seats.
> > I solve this by using 2 CR seals each of which is 1/2 the thickness of the
> > original.
> > I'm a little confused as to how you get a steering box in a lathe???
> > Michael S
> > BN1 #174
> > ------------------------------
> > From: Per Schoerner <per@schoerner.se>
> > Sent: â??14/â??06/â??2015 5:45 p.m.
> > To: healeys@autox.team.net
> > Subject: Re: [Healeys] Steering Box and Wire Wheel Questions--BJ8
> >
> > Hi
> > On the other hand, when you have done all this you will find that it
> > didn't help, it will still leak. It's because of that oil seal that
> > doesn't prevent oil leaks. Magnus Karlsson helped me to put a proper oil
> > seal in the box, and that helps. It involves using the lathe and enlarge
> > the oil seal seat, so a modern seal will fit.
> > And while you're in there you should also replace the bush.
> >
> > Best, Per
> >
> > Michael skrev den 2015-06-14 23:15:
> >
> > > Bottom line for me is spend the time removing the box which will allow
> > > you to do the seal replacement properly.
> > >
> > _______________________________________________
> > Support Team.Net http://www.team.net/donate.html
> > Suggested annual donation  $12.75
> > Archive: http://www.team.net/archive
> > Forums: http://www.team.net/forums
> >
> > Healeys@autox.team.net
> > http://autox.team.net/mailman/listinfo/healeys
> >
> > Unsubscribe/Manage:
> > http://autox.team.net/mailman/options/healeys/michaelsalter@gmail.com
> >
> >
> > _______________________________________________
> > Support Team.Net http://www.team.net/donate.html
> > Suggested annual donation  $12.75
> > Archive: http://www.team.net/archive
> > Forums: http://www.team.net/forums
> >
> > Healeys@autox.team.net
> > http://autox.team.net/mailman/listinfo/healeys
> >
> > Unsubscribe/Manage:
> > http://autox.team.net/mailman/options/healeys/michael.oritt@gmail.com
> >
> >
> >

_______________________________________________
Support Team.Net http://www.team.net/donate.html
Suggested annual donation  $12.75
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys

Unsubscribe/Manage: 
http://autox.team.net/mailman/options/healeys/mharc@autox.team.net

<Prev in Thread] Current Thread [Next in Thread>