Another good tool for loosening and tightening the temperature bulb nut is a
5/8" deep socket with a long cut up one side.
Fit the socket over the nut with the capillary tube protruding through the cut
and then install and tighten a hose clamp around the socket, down near the
open end to will prevent the socket from spreading.
Michael S
-----Original Message-----
From: "Oudesluys" <coudesluijs@chello.nl>
Sent: b2013-b09-b01 4:28 AM
To: "healeys@autox.team.net" <healeys@autox.team.net>
Subject: Re: [Healeys] water temp/oil gauge
Original gauges always have a spiral wire wound around the capillary
tube. Repaired gauges or reproductions often have a woven stainless
steel sheath.
Kees Oudesluijs
Op 1-9-2013 7:28, Bob Spidell schreef:
> We've had a couple of these rebuilt, by two different shops. In both
> cases, the original capillary tube with a 'metal cloth' sheath was
> replaced by a similar tube with a wound wire wrap. Besides being
> slightly larger in diameter, I presume you'd lose points in concours.
>
> Bob
>
>
> On 8/31/2013 6:09 PM, I Erbs wrote:
>> Thanks
>> Ether way, repaired or replaced same difference. Just means there is no
>> special concern if I cut it ,:)
>> Thanks
>>
>> Ira Erbs
>> Portland, OR
>> please excuse typos. Sent from my phone
>> On Aug 31, 2013 6:07 PM, "Patrick & Caroline Quinn"
>> <p_cquinn@tpg.com.au>
>> wrote:
>>
>>> G'day Ira
>>>
>>> Like so many lost emails, mobile calls, file transfers once you cut the
>>> tube
>>> it will all end up in the ether.
>>>
>>> The tube from the sending bulb to the gauge is full of ether. Please
>>> don't
>>> ask what sort of ether as I know there are a few. Anyway my
>>> understanding
>>> is
>>> once the tube is cut it can't be repaired. So you will have to have
>>> a new
>>> one fitted by an instrument specialist to the gauge.
>>>
>>> Best to look around for another one.
>>>
>>> Hoo Roo
>>>
>>> Patrick Quinn
>>> Blue Mountains, Australia
>>>
>>> -----Original Message-----
>>> From: healeys-bounces@autox.team.net [mailto:
>>> healeys-bounces@autox.team.net]
>>> On Behalf Of I Erbs
>>> Sent: Sunday, 1 September 2013 10:05 AM
>>> To: Ahealey help
>>> Subject: [Healeys] water temp/oil gauge
>>>
>>> OK, I figured out why my water temp sender was leaking. The nut has
>>> been
>>> rounded off and I was never able to torque it enough to completely
>>> tighten
>>> the nut. So I guess my only option is to cut the capillary tube and
>>> use my
>>> special removal socket to get the damn thing out of the head.
>>> Question one: what will be released when I cut the tube?
>>> two, what is the best way to cut so it can be repaired?
>>> three. anyone have a working/rebuilt unit I can buy or borrow until
>>> mine is
>>> rebuilt. I'd love tro drive my car before the rainy season hits in
>>> earnest.
>>>
>>> Thanks
>>>
>>> Ira Erbs
>>> IT Teacher
>>> and Consultant
>>>
>>> Portland, OR
>>>
>>>
>>>
>
>
--
Kees Oudesluijs
Dorpsstraat 183
2995XG Heerjansdam
T: 078-677 1233
E: coudesluijs@chello.nl
Technische commissie Jensen Healey en GT
Het Jensen Genootschap Holland
www.jensenholland.nl
Archive: http://www.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
http://autox.team.net/mailman/options/healeys/michaelsalter@gmail.com
_______________________________________________
Archive: http://www.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
|