| To: | healeys@autox.team.net |
|---|---|
| Subject: | [Healeys] water pump bearings |
| From: | john spaur <jmsdarch@sbcglobal.net> |
| Date: | Tue, 29 May 2012 18:52:24 -0700 |
| Delivered-to: | mharc@autox.team.net |
| Delivered-to: | healeys@autox.team.net |
| Dkim-signature: | v=1; a=rsa-sha256; c=relaxed/relaxed; d=sbcglobal.net; s=s1024; t=1338342746; bh=4AoyNFP/RSoOPLrTPvSyNAEMVnGXvxaYZNWBNf9cU/Q=; h=X-Yahoo-Newman-Property:X-YMail-OSG:X-Yahoo-SMTP:Received:Message-Id:X-Mailer:Date:To:From:Subject:Mime-Version:Content-Type; b=fQBuSyCc4ri9tlV/AHmNPiEIxv13ByqEqeaPSJYxFoLCCZxyXT91QlumjWmGQL/xojB8oFCf7w4tDtbvcBdUnbZbk9VTtXmS8hBX6lk0Kxap7jeibnhQYyj91j6Vzz8g3aCHAy4G1vzIK/i8ZYGKv8jSquOO3QY4I6PJzeGs8bA= |
| Domainkey-signature: | a=rsa-sha1; q=dns; c=nofws; s=s1024; d=sbcglobal.net; h=DKIM-Signature:X-Yahoo-Newman-Property:X-YMail-OSG:X-Yahoo-SMTP:Received:Message-Id:X-Mailer:Date:To:From:Subject:Mime-Version:Content-Type; b=fkHuALEcO96g8u2UBGsgoFeia0KOZi3sjr2Vw0fsJaiYyzjBB0QF81MkhuN8zKNhOxter0CosCJ8lKAk07VYkBgVrMbYJ4q9BgeG0lJfw18qk1q4aAapXnCgKGqxMJwGCJLbF1Z8EUIOsHAfXQ0lqa4I7yGX4gjdgZHnwnJpVfw= ; |
| List-archive: | <http://autox.team.net/pipermail/healeys> |
| List-help: | <mailto:healeys-request@autox.team.net?subject=help> |
| List-id: | Austin Healey Discussion <healeys.autox.team.net> |
| List-post: | <mailto:healeys@autox.team.net> |
| List-subscribe: | <http://autox.team.net/mailman/listinfo/healeys>, <mailto:healeys-request@autox.team.net?subject=subscribe> |
| List-unsubscribe: | <http://autox.team.net/mailman/options/healeys>, <mailto:healeys-request@autox.team.net?subject=unsubscribe> |
| Sender: | healeys-bounces@autox.team.net |
I have my two water pumps with 3/8" pulley's disassembled; one
original with the oil screw and one without. The new one without the
oil hole appears to have permanently lubricated bearings. They both
have a small shaft through bearings that are fitted to a larger shaft
that is pressed into the water pump housing. The other does not but
both shafts with the bearings appear very similar.
The bearings in the new shaft seam smooth with a little bit of end play back and forth. About .008 - it's hard to measure. Does that sound like it is good? Is the shaft just pressed through the bearings? That's what it looks like. Are the bearings available? Any thoughts on rebuilding the pump? John Spaur San Jose, CA '62 BT7 _______________________________________________ Support Team.Net http://www.team.net/donate.html Suggested annual donation $12.75 Archive: http://www.team.net/archive Forums: http://www.team.net/forums Healeys@autox.team.net http://autox.team.net/mailman/listinfo/healeys Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/mharc@autox.team.net |
| <Prev in Thread] | Current Thread | [Next in Thread> |
|---|---|---|
| ||
| Previous by Date: | [Healeys] shows on Velocity channel, Bob Haskell |
|---|---|
| Next by Date: | [Healeys] water pump bearings, john spaur |
| Previous by Thread: | [Healeys] shows on Velocity channel, Bob Haskell |
| Next by Thread: | Re: [Healeys] water pump bearings, Chris Dimmock |
| Indexes: | [Date] [Thread] [Top] [All Lists] |