To: | Derek Job <derek.c.job@gmail.com> |
---|---|
Subject: | Re: [Healeys] Installation of FIA approved cut out switch |
From: | Michael Oritt <michael.oritt@gmail.com> |
Date: | Fri, 11 May 2012 12:56:35 -0400 |
Cc: | Forum <Healeys@autox.team.net> |
Delivered-to: | mharc@autox.team.net |
Delivered-to: | healeys@autox.team.net |
Dkim-signature: | v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=20120113; h=mime-version:in-reply-to:references:date:message-id:subject:from:to :cc:content-type; bh=oRedGVG3Z3DpcLPzIUmRx3h80pSBExX35qyCGFaje+w=; b=BlT52lUwKu/K4Kq5+nF/9r7wEXzp+kTfj84s8iZSki6xw+XsLY/fvCUpkI0+D0dX5T bK6GIE8zvZVhnL6VgYASutSVO/xhY85Bc2RctnhdxCnpRbr4rY76Rcr7X6hmi4QIUKna Bqe4saWbO9je/vieo8PvbztQ1V38Lop6NSlcqq0aBjlRL105QBwbrAaWcST6n++72PcD yuPIas9r7esaV0SqGOFoPNXIgAA1nuAWllAqTLPEPkVVFfUpLCIbnpQGs921DedaabFf uRZhkjBeJg3DUkuFq8/zz4JfBlD9c4H1rel363MVQ8H/dvsZ/StDM3eFms+Vt4FC66ja WTfA== |
In-reply-to: | <CAAh8et==0nnWhwdGTCmb7f+vi2YUwg_KsHNpKh1X=qm_nx73tA@mail.gmail.com> |
List-archive: | <http://autox.team.net/pipermail/healeys> |
List-help: | <mailto:healeys-request@autox.team.net?subject=help> |
List-id: | Austin Healey Discussion <healeys.autox.team.net> |
List-post: | <mailto:healeys@autox.team.net> |
List-subscribe: | <http://autox.team.net/mailman/listinfo/healeys>, <mailto:healeys-request@autox.team.net?subject=subscribe> |
List-unsubscribe: | <http://autox.team.net/mailman/options/healeys>, <mailto:healeys-request@autox.team.net?subject=unsubscribe> |
References: | <CAAh8et==0nnWhwdGTCmb7f+vi2YUwg_KsHNpKh1X=qm_nx73tA@mail.gmail.com> |
Sender: | healeys-bounces@autox.team.net |
Derek-- I believe the second set of contacts is designed to ground the alternator. If you have a one-wire alternator then simply run a lead from the alternator to one of the terminals and the other through a resistor and then to ground. If you have a three-wire alternator you'll have to ask someone smarter than me. Yes, you can either disconnect the b/w wire from the coil or if you wish to maintain original appearance leave it connected and cut it somewhere else in its length and insulate the end of the wire so the coil does not inadvertently get grounded. Best--Michael Oritt On Fri, May 11, 2012 at 10:52 AM, Derek Job <derek.c.job@gmail.com> wrote: > Hi all, > > I've just ordered the above switch and Ive been reading up in preparation > for installation. The FIA approve cut out has 2 big terminal for the live > battery feed in and out then 2 pairs of extra terminals. One pair goes on > the circuit between the coil and the ignition switch and the other pair go > between the 'main electrical feed circuit' (as named in the instructions) > and a 3 ohm resistor to earth. > > For the first pair I guess I just take the existing white wire that goes > from coil to ignition and route it from the coil to the switch and then > from the switch to the ignition. > > Re the second pair, which connection would be best to acess the main > electrical feed circuit? The switch will be mounted on the dashboard. > > I will remove the battery cutoff switch in the boot. Can I just simply > disconnect and remove the black and white wire that runs from the cut off > switch to the coil? > > > thanks > > Derek > www.healeysix.net > _______________________________________________ > Support Team.Net http://www.team.net/donate.html > Suggested annual donation $12.75 > Archive: http://www.team.net/archive > Forums: http://www.team.net/forums > > Healeys@autox.team.net > http://autox.team.net/mailman/listinfo/healeys > > Unsubscribe/Manage: > http://autox.team.net/mailman/options/healeys/michael.oritt@gmail.com _______________________________________________ Support Team.Net http://www.team.net/donate.html Suggested annual donation $12.75 Archive: http://www.team.net/archive Forums: http://www.team.net/forums Healeys@autox.team.net http://autox.team.net/mailman/listinfo/healeys Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/mharc@autox.team.net |
<Prev in Thread] | Current Thread | [Next in Thread> |
---|---|---|
|
Previous by Date: | [Healeys] FW: Healey "Security" Circuit, Jonas Payne |
---|---|
Next by Date: | [Healeys] Healey "Security" Circuit, Bob Spidell |
Previous by Thread: | [Healeys] Installation of FIA approved cut out switch, Michael Oritt |
Next by Thread: | [Healeys] Healey "Security" Circuit, Jonas Payne |
Indexes: | [Date] [Thread] [Top] [All Lists] |